Hi,
I have a machine that sits on 10.2 network.
I need to ssh from this to another box that is on both 10.125 & 10.140 VLANs
what should I need to do?
Thanks! (3 Replies)
I want to make static route how would I proceed?
I'm using "route add DestinationIP gatewayIP hop to 1
I would like to make this permanent, so when it reboots I don't want to loose it, would I do this in netconf file? If so where?
I did a search got this site, it didn't help much. ... (2 Replies)
#netstat -nr (shows the following with more static routes)
192.168.18.202 10.129.155.1 UGH 0 29 en0 - -
and i just want to remove the above one
i tried
#smitty rmroute
destination type= net
dest add = 192.168.18.202
default gateway= 10.129.155.1
net... (1 Reply)
Hi guys,
sorry for asking noob question.
When do we really need to add a static route on the server?
I encounter this situation whereby a client trigger a network packet to the destination but the destination does not know how to return the traffic back to the client (source).
The issue was... (4 Replies)
Please , I have a problem
I have add a statis route on Solaris 10, but after this, the network interface of Server was Offline.
The system is in cluster mode (3.2)
route add -net 10.10.1.128 -netmask 255.255.255.128 10.10.1.51
-------------------
lo0:... (1 Reply)
Hi,
Using Centos, under /etc/rc5.d, I wrote a quick script to add my static route when the server gets rebooted. The script doesn't get executed. I did set the permission to 777. After I reboot the server, if I execute, it works manually.
I do this all the time on Solaris and never had... (5 Replies)
Anyone know how to edit a static route in AIX? I find myself deleting and then recreating the route with the new information. Would be nice to know how to edit the route. (3 Replies)
Hello Guys..
I am facing this weird problem of static route not added after reboot!!
Following is my route-<interface> file..
# cat /etc/sysconfig/network-scripts/route-eth0
ADDRESS0=172.31.0.1
NETMASK0=255.255.255.255
GATEWAY0=192.168.208.1
ADDRESS1=172.31.15.2... (3 Replies)
Hi all,
This may be the basic question of Routing but I am a sort of new to networking so I am asking.
Do I need to put route for my router's LAN port ip to WAN (serial) port ip Or the router itself can communicate between its ports without routes.
lan (172.26.40.5) ... (3 Replies)
Discussion started by: dextergenious
3 Replies
LEARN ABOUT SUSE
irsend
IRSEND(1) FSF IRSEND(1)NAME
irsend - basic LIRC program to send infra-red commands
SYNOPSIS
irsend [options] DIRECTIVE REMOTE CODE [CODE...]
DESCRIPTION
Asks the lircd daemon to send one or more CIR (Consumer Infra-Red) commands. This is intended for remote control of electronic devices such
as TV boxes, HiFi sets, etc.
DIRECTIVE can be:
SEND_ONCE - send CODE [CODE ...] once
SEND_START - start repeating CODE
SEND_STOP - stop repeating CODE
LIST - list configured remote items
SET_TRANSMITTERS - set transmitters NUM [NUM ...]
SIMULATE - simulate IR event
REMOTE is the name of a remote, as described in the lircd configuration file.
CODE is the name of a remote control key of REMOTE, as it appears in the lircd configuration file.
NUM is the transmitter number of the hardware device.
For the LIST DIRECTIVE, REMOTE and/or CODE can be empty:
LIST "" "" - list all configured remote names
LIST REMOTE "" - list all codes of REMOTE
LIST REMOTE CODE - list only CODE of REMOTE
The SIMULATE command only works if it has been explicitly enabled in lircd.
-h --help
display usage summary
-v --version
display version
-d --device
use given lircd socket [/var/run/lirc/lircd]
-a --address=host[:port]
connect to lircd at this address
-# --count=n
send command n times
EXAMPLES
irsend LIST DenonTuner ""
irsend SEND_ONCE DenonTuner PROG-SCAN
irsend SEND_ONCE OnkyoAmpli VOL-UP VOL-UP VOL-UP VOL-UP
irsend SEND_START OnkyoAmpli VOL-DOWN ; sleep 3
irsend SEND_STOP OnkyoAmpli VOL-DOWN
irsend SET_TRANSMITTERS 1
irsend SET_TRANSMITTERS 1 3 4
irsend SIMULATE "0000000000000476 00 OK TECHNISAT_ST3004S"
FILES
/etc/lirc/lircd.conf
Default lircd configuration file. It should contain all the remotes, their infra-red codes and the corresponding timing and wave-
form details.
DIAGNOSTICS
If lircd is not running (or /var/run/lirc/lircd lacks write permissions) irsend aborts with the following diagnostics:
"irsend: could not connect to socket"
"irsend: Connection refused" (or "Permission denied").
SEE ALSO
The documentation for lirc is maintained as html pages. They are located under html/ in the documentation directory.
lircd(8), mode2(1), smode2(1), xmode2(1), irrecord(1), irw(1), http://www.lirc.org.
irsend 0.8.7pre1 May 2010 IRSEND(1)