|
|
Sponsored Content
Operating Systems
Solaris
ZFS - list of disks used in a pool
Post 302431450 by frum on Tuesday 22nd of June 2010 02:34:15 AM
06-22-2010
|
|
10 More Discussions You Might Find Interesting
1. Solaris
Hi all
I plan to install Solaris 10U6 on some SPARC server using ZFS as root pool, whereas I would like to keep the current setup done by VxVM:
- 2 internal disks: c0t0d0 and c0t1d0
- bootable root-volume (mirrored, both disks)
- 1 non-mirrored swap slice
- 1 non-mirrored slices for Live... (1 Reply)
Discussion started by: blicki
1 Replies
2. Solaris
# zpool import
pool: emcpool1
id: 5596268873059055768
state: UNAVAIL
status: One or more devices are missing from the system.
action: The pool cannot be imported. Attach the missing
devices and try again.
see: Sun Message ID: ZFS-8000-3C
config:
emcpool1 ... (7 Replies)
Discussion started by: fugitive
7 Replies
3. Infrastructure Monitoring
Here are the details.
cnjr-opennms>root$ zfs list
NAME USED AVAIL REFER MOUNTPOINT
openpool 20.6G 46.3G 35.5K /openpool
openpool/ROOT 15.4G 46.3G 18K legacy
openpool/ROOT/rds 15.4G 46.3G 15.3G /
openpool/ROOT/rds/var 102M ... (3 Replies)
Discussion started by: pupp
3 Replies
4. Solaris
I created a pool the other day. I created a 10 gig files just for a test, then deleted it.
I proceeded to create a few files systems. But for some reason the pool shows 10% full, but the files systems are both at 1%? Both files systems share the same pool.
When I ls -al the pool I just... (6 Replies)
Discussion started by: mrlayance
6 Replies
5. Solaris
I need to migrate an existing raidz pool to a new raidz pool with larger disks. I need the mount points and attributes to migrate as well. What is the best procedure to accomplish this. The current pool is 6x36GB disks 202GB capacity and I am migrating to 5x 72GB disks 340GB capacity. (2 Replies)
Discussion started by: jac
2 Replies
6. Solaris
Other than export/import, is there a cleaner way to rename a pool without unmounting de FS?
Something like, say "zpool rename a b"?
Thanks. (2 Replies)
Discussion started by: verdepollo
2 Replies
7. Solaris
Hi!
I would also like to know if I need first to create a pool before I can mirror my disks inside that pool.
My first disk is c7t0d0s0 and my second disk is c7t2d0s0 as seen in the figure below.
I would create a pool named rpool1 for this 2 disks.
# zpool create rpool1 c7t0d0p0 c7t2d0p0 ... (18 Replies)
Discussion started by: CarlosP
18 Replies
8. Solaris
installed Solaris 11 Express on my server machine a while ago. I created a Z2 RAID over five HDDs and created a few ZFS filesystems on it.
Once I (unintentionally) managed to fill the pool completely with data and (to my surprise) the filesystems stopped working - I could not read/delete any... (3 Replies)
Discussion started by: RychnD
3 Replies
9. Solaris
I have a branded zone txdjintra that utilizes a pool named Pool_djintra that is no longer required. There is a 150 Gig Lun assigned to the pool that I need to reassign to another branded zone txpsrsrv07 with a pool named Pool_txpsrsrv07 on the same sun blade. What is the process to do this?
... (0 Replies)
Discussion started by: jeffsr
0 Replies
10. Solaris
I have a newly created zpool, and I have set compression on, for the whole pool:
# zfs set compression=on newPool
Now I have zfs send | zfs receive lot of snapshots to my newPool, but the compression is gone. I was hoping that I would be able to send snapshots to the new pool (which is... (0 Replies)
Discussion started by: kebabbert
0 Replies
LEARN ABOUT DEBIAN
zdb
zdb(8) System Administration Commands zdb(8) NAME
zdb - ZFS debugger SYNOPSIS
zdb pool DESCRIPTION
The zdb command is used by support engineers to diagnose failures and gather statistics. Since the ZFS file system is always consistent on disk and is self-repairing, zdb should only be run under the direction by a support engineer. If no arguments are specified, zdb, performs basic consistency checks on the pool and associated datasets, and report any problems detected. Any options supported by this command are internal to Sun and subject to change at any time. EXIT STATUS
The following exit values are returned: 0 The pool is consistent. 1 An error was detected. 2 Invalid command line options were specified. ATTRIBUTES
See attributes(5) for descriptions of the following attributes: +-----------------------------+-----------------------------+ | ATTRIBUTE TYPE | ATTRIBUTE VALUE | +-----------------------------+-----------------------------+ |Availability |SUNWzfsu | +-----------------------------+-----------------------------+ |Interface Stability |Unstable | +-----------------------------+-----------------------------+ SEE ALSO
zfs(8), zpool(8), attributes(5) SunOS 5.11 31 Oct 2005 zdb(8)