ufsrestore T5240 Post: 302430871

9 More Discussions You Might Find Interesting

1. Solaris

raidctl on SUN T5240

Setting up a T5240 with two disks c1t0d0 and c1t1d0. I am trying to use raidctl but when I issue. raidctl -l I get Controller 1 Disk: 0.0.0 Disk: 0.1.0 So I try raidctl -c '0.0.0 0.1.0' -r 1 1 and I get "Array in use." I try

2. Solaris

cannot plumb nxge on T5240

its a fresh installation. during the OS setup, it did not prompt for IP, netmask and gateway. using Solaris 10 08/07 update 4. I tried to plumb manually but encountered no such interface error. but nxge interfaces can be greped from the /etc/path_to_inst file. getting similar error on...

3. Solaris

T5240 netmgmt port not blinking

I was trying to configure the netmgmt from the serial and set commitpending to true. However, the netmgmt port is not up and blinking. I tried to connect using my notebook directly to the netmgmt port and am not able to ping as well. Previouly i was doing the firmware upgrade using the webconsole....

4. Solaris

SUN T5240 vs M3000

Hi, We are planning to buy new server for our data center. Sun T5240 or M3000 which one have better performance, we are going to create many dt sessions in this server. So, i need your suggestions. RJS

5. Solaris

Bizarre Sun T5240 behavior

Hi - I have a T5240 with 7 LDOMS configured. One night, network comm was broken somehow. Nobody was doing anything on the machine at the time. Here is what I saw in messages: WARNING: nxge3 : nxge_dma_mem_alloc: ddi_dma_mem_alloc kmem alloc failed WARNING: nxge3 : nxge_alloc_rx_buf_dma:...

6. Solaris

Disable multithreading option on T5240

Hi Gurus Can any one tell me the process of disabling the multithreading option on T5240 server and my OS is on LDOM, having one physical processor with 8 core & 8 thread per core Regards

7. Solaris

Cannot configure RAID on T5240

Hi ! I've been given a T5240 with 4 disks and 2 HBA cards (but no array connected). I did a factory reset on SP and NVRAM clean on OBP because the server had been used before. I boot cdrom in single mode and try to create a hw mirror with disks from c1... but only c2 is seen by raidctl. ...

8. Solaris

Question: # of ldoms on T5240 with 2 T2 US 8 core

I have a T5240 with 2 T2 US 8 core.. Theoretically how many ldoms can I configure?

9. Solaris

Using a Modem on a T5-2 or a T5240

Hi Folks, Just a quick question - hopefully! I have an application currently running on a V890 with Solaris 9, I'd like to move this to either one of our T-5's or one of the T5240's in a Legacy container on an LDOM - but the fly in the ointment is the application still uses a standard Hayes...

LEARN ABOUT NETBSD

uk

UK(4)							   BSD Kernel Interfaces Manual 						     UK(4)

NAME

     uk -- SCSI user-level driver

SYNOPSIS

     uk* at scsibus? target ? lun ?

DESCRIPTION

     The uk driver provides support for a process to address devices on the SCSI bus for which there is no configured driver.

     A SCSI adapter must also be separately configured into the system before this driver makes sense.

KERNEL CONFIGURATION

     If a count is given, that number of uk devices will be configured into the NetBSD kernel.

IOCTLS

     The uk driver has no ioctls of its own but rather acts as a medium for the generic scsi(4) ioctls.  These are described in <sys/scsiio.h>.

FILES

     /dev/uk[0-255]  unknown SCSI devices.

DIAGNOSTICS

     All scsi(4) debug ioctls work on uk devices.

SEE ALSO

     ioctl(2), cd(4), ch(4), scsi(4), sd(4), ss(4), st(4)

HISTORY

     The uk driver appeared in 386BSD 0.1.

BSD
								 October 11, 1993							       BSD