06-19-2010
route add
I have built a new linux server, via a iLo connection.
and I am trying to connect via my desktop to the server I have just built to the management port eth0 via putty.
Please could some one advise how to connect to this server from my desktop. Do i need to create add a route access on the server ?
Thank you
10 More Discussions You Might Find Interesting
1. AIX
Hello ,
We have 3 rs/6000 server's running aix on our local network, so each time I try to ping one of these servers we get a "network is down" error , I've been instructed to use to route add command which is ...
#route add server.ip router.ip
after this the ping command works fine ,... (6 Replies)
Discussion started by: cubicle^dweller
6 Replies
2. IP Networking
I have two networks connected by cisco routers. My first subnet is 192.168.0.0 and my second is 192.168.1.0.
My SCO unix machine is on the 192.168.1.0 subnet with an IP of 192.168.1.231. It can see the entire .1.0 subnet but nothing on the other network.
My cicso router(gateway) to the other... (6 Replies)
Discussion started by: agoodrich
6 Replies
3. HP-UX
Hi,
My H-UX box has the GW pointing to 10.10.10.1 and I need add it a new route pointing to 192.168.80.x with the GW 10.10.10.13
I tried with:
#route add 192.168.80.2 255.255.255.255 10.10.10.13
but I get: add net 192.168.80.0: gateway 255.255.255.0: Network is unreachable
I tried with... (4 Replies)
Discussion started by: efrenba
4 Replies
4. IP Networking
I have a system that i want to reach via a vpn created vi a fierwall.The fierwall in an other system.
The ip i am trying to get to is 172.16.4.48
I need to get to it via the hme1 interface.
The vpn gateway has this ip 172.30.50.1
I need to clean up the routing table and make this work; or is it... (5 Replies)
Discussion started by: waterboy
5 Replies
5. Solaris
Hi,
I am trying to add route command in Solaris 10 machine in the following fashion:
route add -host 10.8.112.10 180.144.1.250 -interface lo0:1
this command fails with an error "lo0:1: bad value"
I want to add a route to 10.8.112.10 that picks 180.144.1.250 as the gateway via the... (3 Replies)
Discussion started by: sudhir_shet
3 Replies
6. Solaris
Hey Guys:
I am trying to add a route for assign a network interface to the traffic to/from a specific net, but allways to get the same system message : network is unreacheable
root@ColectorDMSCNT # route add net 200.44.46.0/24 161.196.84.196 1
add net 200.44.46.0/24: gateway... (2 Replies)
Discussion started by: aggadtech08
2 Replies
7. Solaris
Hi need to add 2 routes, one on each server.
I know the route add comand but I have always been given the parameters to put in.
I need a route in each of the 2 following servers to be able to ping and ssh between them. But how do i know which netmask to put in the route add command ?
In... (6 Replies)
Discussion started by: vettec3
6 Replies
8. Solaris
I need to add a new route on solaris10 machine.
I want that all traffic on the 23 port (telnet) use 192.168.200.1 gateway.
How I do ?
Thank you in advance. (1 Reply)
Discussion started by: arfry
1 Replies
9. Solaris
Hi Solaris Experts,
I am trying to add a routing table entry on our 5.1 Generic_144488-12 sun4v sparc Solaris 10 SUNW,SPARC-Enterprise-T5220 so that it is possible to ping 10.56.9.34 node
# netstat -rnv
IRE Table: IPv4
Destination Mask Gateway Device Mxfrg Rtt Ref
Flg Out In/Fwd ... (2 Replies)
Discussion started by: gjackson123
2 Replies
10. IP Networking
Add explicit route to 10.128.255.41/32 , gateway: 10.128.201.254
if not working, please try gateway through management port: 10.128.55.254
Just want to double confirm if this would be the correct command
#route add -net 10.128.255.41/32 10.128.201.254
And if didnt work
#route add... (1 Reply)
Discussion started by: Thilagarajan
1 Replies
LEARN ABOUT SUSE
vncserver
vncserver(1) TightVNC vncserver(1)
NAME
vncserver - a wrapper to launch an X server for VNC.
SYNOPSIS
vncserver [:display] [-geometry widthxheight] [-depth depth] [-pixelformat rgbNNN|bgrNNN] [-name desktop-name] [Xvnc-options...]
vncserver -kill :display
vncserver -help
DESCRIPTION
vncserver is a wrapper script for Xvnc, the free X server for VNC (Virtual Network Computing). It provides all capabilities of a standard X
server, but does not connect to a display for itself. Instead, Xvnc creates a virtual desktop you can view or control remotely using a VNC
viewer.
OPTIONS
You can add Xvnc options at the command line. They will be added to the invocation of Xvnc without changes. The options provided by the
vncserver itself are as follows:
:display
The display number to use. If omitted, the next free display number is used.
-geometry widthxheight
Set desktop width and height.
-depth depth
Set the colour depth of the visual to provide, in bits per pixel. Must be a value between 8 and 32.
-pixelformat rgbNNN|bgrNNN
Set colour format for pixels representation. The viewer can do the conversion to any other pixel format, but it is faster if the
depth and pixel format of the server is the same as the equivalent values on the viewer display.
-name string
This specifies the name of the desktop.
-kill :display
Stops the session running on the specified display.
-help Prints a short usage notice to stderr.
EXAMPLES
vncserver
Invokes Xvnc on the next available display and with suitable defaults.
vncserver :1
Invokes Xvnc on display :1.
vncserver -geometry 800x600 -depth 16 :1
Invokes Xvnc on display :1 with desktop size of 800x600 pixels and color depth of 16 bits per pixel.
vncserver -kill :1
Shuts down Xvnc server on display :1.
SEE ALSO
Xvnc(1), vncviewer(1), vncpasswd(1), vncconnect(1)
AUTHORS
Original VNC was developed in AT&T Laboratories Cambridge. TightVNC additions were implemented by Constantin Kaplinsky. Many other people
participated in development, testing and support.
Man page authors:
Marcus Brinkmann <Marcus.Brinkmann@ruhr-uni-bochum.de>,
Tim Waugh <twaugh@redhat.com>,
Constantin Kaplinsky <const@tightvnc.com>
August 2006 vncserver(1)