06-18-2010
Can you show us the contents of /etc/conf/cf.d/mscsi and the contents of /usr/adm/messages, only for the last boot.
8 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
I have a hp d 350 running on 10.2,im having a problem with the dds2 tape drive whenever i tried backing up larger files...i have remove the tape driver and add it using sam again but still the tape drive is not working .....is there a solution to this problem?
# tar cvf /dev/rmt/0m priso.ds
a... (3 Replies)
Discussion started by: giriplug
3 Replies
2. UNIX for Dummies Questions & Answers
Hi,
I need to restore my tape backup, when I type "tape status" it gives;
status : ready beginning-of-tape write-protected
soft errors : 0
hard errors : 0
underruns : 3
but... (4 Replies)
Discussion started by: alisevA3
4 Replies
3. Solaris
I have been working on this one for a few days. Any help/advice would be greatly appreciated.
Hardware
Machine: Sun Blade 2000
Tape Drives: HP Ultrium LTO2 002 (x2) (Inside an L40)
Software
OS: Solaris 8
st.conf uncommented lines:
probe-scsi-all reports both drives.
/dev/rmt is... (2 Replies)
Discussion started by: lucesean
2 Replies
4. UNIX for Advanced & Expert Users
Hello sir
Please I just have tape blocked inside the tape drive of my server. My server have 2 tape drives configured but only one is available (rmt0). The problem is that i have a separed tape drive ready to be connected to my server and i wan to know how to make available the second tape drive ?... (0 Replies)
Discussion started by: sobnc
0 Replies
5. AIX
I have tape drive in one Lpar. when i saw that time tape is in defined state. After that i deleted the tape drive using the rmdev -R command. Then fired the cfgmgr -v command. But I am not getting the tape drive. Now the drive is even not in defined state also. It is not shown the tape drive. How... (1 Reply)
Discussion started by: pernasivam
1 Replies
6. Solaris
Hey folks,
Linux admin here, forced to use Opensolaris to try to use ufsdump/ufsrestore to get some data of some old tapes.
I've got Opensolaris 2009.06 on x86 and a Sony SDX-700V.
As a "control" experiment, I booted the system with a Linux live CD and the tape drive worked perfectly.
... (2 Replies)
Discussion started by: eddy_sysad
2 Replies
7. UNIX for Dummies Questions & Answers
Hi,
Using Redhat 5.7. I have Quantum tape drive connected to the server. I am trying to install the Netbackup software. Just wondering how can I see the Quantum is connected to the server. is any command I run to see the tape drive is connected?
I used to work on Solaris, I used to do... (1 Reply)
Discussion started by: samnyc
1 Replies
8. HP-UX
I have used ioscan -fnC tape and the system identified the tape drive. what is the command to show a listing of what is on the tape? I have used ls /dev/rmt/rmt0 to no avail. can anyone help?
Thanks in advance (10 Replies)
Discussion started by: Randydog
10 Replies
LEARN ABOUT OSF1
binlog.conf
binlog.conf(4) Kernel Interfaces Manual binlog.conf(4)
NAME
binlog.conf - binlogd configuration file
SYNOPSIS
event_code.priority destination Where: Are the numeric codes specified in binlog.h and the binlogd(8) reference page. An aster-
isk (*) specifies that all events should be selected. The code dumpfile Specifies the recovery of the kernel binary event log buffer from a
crash dump. A severity level cannot be specified. Filters selected events as severe, high, and low. An asterisk (*) specifies that all
events should be selected. A local file pathname to a log file, or a remote system hostname for remote logging of events.
DESCRIPTION
The /etc/binlog.conf file is a system file that enables you to configure or filter events that are to be logged by the binary error logger,
binlogd.
The binlogd daemon ignores blank lines and lines that begin with an octothorpe (#). You can specify # as the first character in a line to
include comments in the file or to disable an entry.
If you want the binlogd daemon to use a configuration file other than the default, specify the file name with the following command: # bin-
logd -f config_file Note that EVM subscribes to binlog events by default, and any configuration options you select will affect what events
are available to EVM. You can filter and select binlog events using EVM utilities, as described in the EVM(5) reference page.
EXAMPLES
The following is a sample /etc/binlog.conf file: # # binlogd configuration file # #format of a line: event_code.priority destination
# # where: event_code - see codes in binlog.h and man page, # * = all events # priority - severe, high, low, * = all priorities #
destination - local file pathname or remote system # hostname
*.* /usr/adm/binary.errlog dumpfile /usr/adm/crash/binlogdumpfile crdlog /usr/adm/binary.crdlog 102.high
/usr/adm/disk.errlog
FILES
/etc/binlog.conf
/etc/binlog.auth - Authorization file for remote logging.
/usr/sys/include/dec/binlog/binlog.h - Common components of a binary event log record.
RELATED INFORMATION
Commands: /usr/sbin/binlogd(8), EVM(5)
System Administration delim off
binlog.conf(4)