06-16-2010
Quote:
I think that the simplest solution is to:
1. Acquire a desktop system (IDE/SATA) that has enough memory and disk space to accommodate your application.
2. Download a 30 day demo version of Microlite Edge
http://microlite.com
3. Install this on your current system.
4. Create a backup to DVD, You will need a DVD Writer in the old system
5. Using the Microlite software, you can create an emergency boot cd for the target system (IDE).
6. Use the emergency boot cd to boot the new system and restore the backup.
7. Re configure the network card, and printers if necessary.
Hmm. Will the restore to a single IDE drive on the new system be impacted by the Raid 5 SCSI array from the old system?
8 More Discussions You Might Find Interesting
1. Filesystems, Disks and Memory
I am using SCO Unixware 2.1 & some PC clients are connected, suddenly one message appearslike :
UX:strintercept error: dropping message
this message starts coming repeatedly & agtre some time system hangs.I had to reset the system & now the problem is not there.Please suggest, why this is... (0 Replies)
Discussion started by: paprch
0 Replies
2. UNIX for Dummies Questions & Answers
According to this thread: https://www.unix.com/showthread.php?t=1 one guy says However, I cannot find any sco unixware7 iso download link in their download section (http://wdb1.sco.com/clbk_web/owa/dwn_customer), is it really for free, and if that is true, where can I download it?
Thanks, (2 Replies)
Discussion started by: phalcos
2 Replies
3. SCO
Please help me in troubleshooting my problem in Samba?
I tried to instal Samba 3.0.24 in our SCO UnixWare 7.1.4 but after installing the nmbd daemon is not running.
When i check the syslog from /var/adm, the following error appears:
Sep 30 13:04:22 unixeei nmbd: bind failed on port 137... (0 Replies)
Discussion started by: eric_hing
0 Replies
4. SCO
hi,
anybody can give procedure for how to install oracle 8.0.5 in sco unixware 7.1.4. (0 Replies)
Discussion started by: prakrithi
0 Replies
5. SCO
hello,
sco openserver R5
the following error and it fails to load.
init: Command is respawning too rapidily
id: vm "/home/bin/stvm.sh"
init: Comand..etc
id: c02"/etc/start/autostart"
its trying to mount car diagnostic program in vmware, the program location
is in "start" i think? i... (1 Reply)
Discussion started by: hgibbs8129
1 Replies
6. SCO
(sorry my English, is really poor).
I have a SCO Unixware 7.1.1 and I need install in ML350 G3. Reading in google and HP web, make a floppy disks for install, but the options that I have is for network or floppy disk.
How install from CD with patch for HP smart array 532 ??
or
How... (5 Replies)
Discussion started by: xplertor
5 Replies
7. SCO
Hi, I'm new to this Unix world and have taken over looking after the I.T side of things at work, which includes the internal ERP system which runs on a UNIX SCO platform.
My initial worry is what state this is in as its been on site over 20 years.
What would be the first things to check on... (13 Replies)
Discussion started by: Mick_Dundee
13 Replies
8. SCO
Hi,
I need help to install SCO Unixware 7.0.1. Can any one help with any documentation or installation notes for SCO Unixware 7.0.1.
Thank you (1 Reply)
Discussion started by: farhandalvi
1 Replies
LEARN ABOUT SUNOS
addbadsec
addbadsec(1M) System Administration Commands addbadsec(1M)
NAME
addbadsec - map out defective disk blocks
SYNOPSIS
addbadsec [-p] [ -a blkno [blkno...]] [-f filename] raw_device
DESCRIPTION
addbadsec is used by the system administrator to map out bad disk blocks. Normally, these blocks are identified during surface analysis,
but occasionally the disk subsystem reports unrecoverable data errors indicating a bad block. A block number reported in this way can be
fed directly into addbadsec, and the block will be remapped. addbadsec will first attempt hardware remapping. This is supported on SCSI
drives and takes place at the disk hardware level. If the target is an IDE drive, then software remapping is used. In order for software
remapping to succeed, the partition must contain an alternate slice and there must be room in this slice to perform the mapping.
It should be understood that bad blocks lead to data loss. Remapping a defective block does not repair a damaged file. If a bad block
occurs to a disk-resident file system structure such as a superblock, the entire slice might have to be recovered from a backup.
OPTIONS
The following options are supported:
-a Adds the specified blocks to the hardware or software map. If more than one block number is specified, the entire list should be
quoted and block numbers should be separated by white space.
-f Adds the specified blocks to the hardware or software map. The bad blocks are listed, one per line, in the specified file.
-p Causes addbadsec to print the current software map. The output shows the defective block and the assigned alternate. This option
cannot be used to print the hardware map.
OPERANDS
The following operand is supported:
raw_device The address of the disk drive (see FILES).
FILES
The raw device should be /dev/rdsk/c?[t?]d?p0. See disks(1M) for an explanation of SCSI and IDE device naming conventions.
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Architecture |x86 |
+-----------------------------+-----------------------------+
|Availability |SUNWcsu |
+-----------------------------+-----------------------------+
SEE ALSO
disks(1M), diskscan(1M), fdisk(1M), fmthard(1M), format(1M), attributes(5)
NOTES
The format(1M) utility is available to format, label, analyze, and repair SCSI disks. This utility is included with the addbadsec,
diskscan(1M), fdisk(1M), and fmthard(1M) commands available for x86. To format an IDE disk, use the DOS "format" utility; however, to
label, analyze, or repair IDE disks on x86 systems, use the Solaris format(1M) utility.
SunOS 5.10 24 Feb 1998 addbadsec(1M)