Hello, earlier tonight I was installing BETA version of Mandrake Linux 9.0 and I realised I needed to partition my drive. I tried making the partition within mandrake but ther wasnt an option within the mandrake setup. So i go into my WindowsXP and do the disk management option but there want a... (5 Replies)
Can some one point this UNIX newbie to a web site or directions on the steps needed to break a mirror in HP-UNIX to change a bad hard drive. (4 Replies)
Hello everyone.
I am new to Linux so hope some one could help me here.
I have a 30 Gb HD and windows Xp is my O/S, HD is not partitioned,but I want to Partitioned it, so I could Install Knoppix(Linux)on one of the partitioned one, how could I do this? OR should I erase every thing and then... (1 Reply)
Hi,
Going to be applying patches to Sun prod (dev 1st) boxes soon,
I'm going to break the mirror's on 3 file systems on the root disk prior to that (/, /var, /swap),then run 9_Recommended. Then, run it for a day or 2 before re-syncing the mirrors.
But, what if I want to backout of this... (1 Reply)
:confused: ........I have a new hard drive and I need to copy ALL info from the old to the new. I would like to use the dd command. I know the command is as follows......
dd if=/dev/rdsk/c1t1d0s0 of=/dev/rdsk/????????
Where I have the question marks is the problem.
How do I find out what the... (4 Replies)
Hi
I have 2 75GB SCSI hard drives and 2 250GB SATA hard drives which are using RAID Level 1 respectively. I wana have both FTP and Apache installed on them as services. I'm wondering what's the best partitioning schem? I wana use FC3 as my OS, so, I thought I can use the 75GB hard drive as the /... (0 Replies)
Hi,
am a newbie at solaris. Need advice and help on this.
1) How do I break the mirror between 2 hard disks. (wish to keep 1 good hard disk as backup)
2) After remove 1 hard disk and put in new hard disk, how do I initialise or fomat the new hard disk?
3) How do I put back the backup... (3 Replies)
Solaris 10 5/08 on Ultra 40 M2
It boots fine off primary disk but having issues booting off the mirror disk.
I get this error when booting off mirror disk:
Booting 'Solaris 10 ... Mirror disk'
root (hd1,0,a)
Error 22: No such partition
Press any key to continue...
Any... (7 Replies)
We are in the process of migrating storage from one array to another. I know the commands I would use in LVM but I am not very familiar with VxVM.
The goal is to attach the new LUNs from the new array and add them to the disk group. Then mirror the data online to these new LUNs using VxVM... (4 Replies)
Discussion started by: keelba
4 Replies
LEARN ABOUT DEBIAN
halt
HALT(8) Linux System Administrator's Manual HALT(8)NAME
halt, reboot, poweroff - stop the system.
SYNOPSIS
/sbin/halt [-n] [-w] [-d] [-f] [-i] [-p] [-h]
/sbin/reboot [-n] [-w] [-d] [-f] [-i]
/sbin/poweroff [-n] [-w] [-d] [-f] [-i] [-h]
DESCRIPTION
halt notes that the system is being brought down in the file /var/log/wtmp, and then either tells the kernel to halt, reboot or power-off
the system.
If halt or reboot is called when the system is not in runlevel 0 or 6, in other words when it's running normally, shutdown will be invoked
instead (with the -h or -r flag). For more info see the shutdown(8) manpage.
The rest of this manpage describes the behaviour in runlevels 0 and 6, that is when the systems shutdown scripts are being run.
OPTIONS -n Don't sync before reboot or halt. Note that the kernel and storage drivers may still sync. This implies -d.
-w Don't actually reboot or halt but only write the wtmp record (in the /var/log/wtmp file).
-d Don't write the wtmp record.
-f Force halt or reboot, don't call shutdown(8).
-i Shut down all network interfaces just before halt or reboot.
-h Put all hard drives on the system in stand-by mode just before halt or power-off.
-p When halting the system, switch off the power. This is the default when halt is called as poweroff.
DIAGNOSTICS
If you're not the superuser, you will get the message `must be superuser'.
NOTES
Under older sysvinit releases , reboot and halt should never be called directly. From release 2.74 on halt and reboot invoke shutdown(8) if
the system is not in runlevel 0 or 6. This means that if halt or reboot cannot find out the current runlevel (for example, when
/var/run/utmp hasn't been initialized correctly) shutdown will be called, which might not be what you want. Use the -f flag if you want to
do a hard halt or reboot.
The -h flag puts all hard disks in standby mode just before halt or power-off. Right now this is only implemented for IDE drives. A side
effect of putting the drive in stand-by mode is that the write cache on the disk is flushed. This is important for IDE drives, since the
kernel doesn't flush the write cache itself before power-off.
The halt program uses /proc/ide/hd* to find all IDE disk devices, which means that /proc needs to be mounted when halt or poweroff is
called or the -h switch will do nothing.
AUTHOR
Miquel van Smoorenburg, miquels@cistron.nl
SEE ALSO shutdown(8), init(8)
Nov 6, 2001 HALT(8)