06-03-2010
How restart the network interface in AIX?
Hi All,
Please let me know the command to restart the network interface and enable it on boot in AIX, similar to /etc/init.d/network restart in Redhat.
Thanks,
Sunil.K
Moderator's Comments:
|
|
please watch out to post in the right subforum!
|
|
Last edited by DukeNuke2; 06-03-2010 at 04:02 AM..
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi !
Does anyone know how can i get information about my network interface ... if it works in half or full duplex mode !!
Thx in adivance !
Witt (4 Replies)
Discussion started by: witt
4 Replies
2. BSD
hi
howto restart the network with a wireless interface including wpa_supplicant on freeBSD 7.2 without reboot? (3 Replies)
Discussion started by: ccc
3 Replies
3. AIX
Hi,
I am trying to list all the interface present in the given system.
Here is sample program.
i.e. cat 1.c
#include <sys/types.h>
#include <sys/socket.h>
#include <sys/ioctl.h>
#include <sys/dlpi.h>
#include <net/if.h>
/*#include <sys/sockio.h>*/
#include <unistd.h>
#include... (3 Replies)
Discussion started by: jgobbur
3 Replies
4. Solaris
i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ?
Thanks (9 Replies)
Discussion started by: skamal4u
9 Replies
5. UNIX and Linux Applications
Hi,
I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan.
For that I must access to network interface to develope my personal stack based on standard 802.15.4.
Can you help me? I need an explanation for that. (0 Replies)
Discussion started by: berny88
0 Replies
6. IP Networking
Hello,
Please, how can i create a network interface with a routable IP address on linux (ubuntu) ?
AND
How can i desactivate an interface?
Thank you so much for help. (1 Reply)
Discussion started by: chercheur857
1 Replies
7. Solaris
I've one Netra 240
After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces.
I tried to restart and plumb/unplumb with no luck.
ifconfig -a... (7 Replies)
Discussion started by: samer.odeh
7 Replies
8. UNIX for Dummies Questions & Answers
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
9. Red Hat
Hi,
I have 2 machines in production environment:
1. redhat machine for application
2. DB machine (oracle)
The application doing a lot of small read&writes from and to the DB machine.
The problem is that after some few hours the network from the application to the DB becomes very slow and... (4 Replies)
Discussion started by: moshesa
4 Replies
10. Debian
Hello,
I would like to do follow steps.
Set a static IP-Adress on eth0 (For Testing)
Set DHCP on eth0
All steps should be done without a single reboot.
/etc/network/interfaces
iface eth0 inet static
address 192.0.2.7/24
gateway 192.0.2.254How do i perform... (3 Replies)
Discussion started by: int3g3r
3 Replies
LEARN ABOUT OSF1
ip6_setup
ip6_setup(8) System Manager's Manual ip6_setup(8)
NAME
ip6_setup - IPv6 configuration program
SYNOPSIS
/usr/sbin/ip6_setup
DESCRIPTION
The ip6_setup utility allows you to configure the IPv6 networking software on your system.
To run ip6_setup, enter the following command and then answer the questions: # ip6_setup
You must know your Internet Protocol Version 6 (IPv6) address. If your network uses subnet routing, you must know the subnet mask for your
network. The network manager should be able to provide you with the information that you need.
After the ip6_setup command completes, the network services on the system can be restarted manually with the following command: #
/usr/sbin/rcinet restart
Before you restart the network services with the preceding command, warn the users that the network services on the system are being
removed. File systems that were not mounted using the /etc/fstab file or the automount command must be unmounted with the unmount command.
You must remount these file systems using the mount command after the network is started on your system.
Alternatively, you can reboot the system with the following command: # /usr/sbin/shutdown -r now
FILES
Specifies the host name file. Specifies the environment variables that define the network configuration on your system. Specifies the
trusted hosts file. Specifies the network name file. Specifies Internet routing information. Specifies Internet routing information.
SEE ALSO
Commands: mount(8), rcinet(8)
Files: gateways(4), hosts(4), hosts.equiv(4), networks(4), routes(4).
Network Administration
ip6_setup(8)