When I am trying to boot my SUN Netra 240 Machine its giving some boot error.
> {1} ok boot -i
Code:
> Boot device: /pci@1c,600000/scsi@2/disk@0,0:a File and args: -i
> Boot load failed.
> The file just loaded does not appear to be executable.
> {1} ok
I tried to boot it from cdrom and monted the boot diskt to /a and tried
installboot to install bootblk. installboot and fsck ran fine and when I rebooted , it again gave the same error.
Just curious does this mean the disk is gone ? Below finding doesn't show any hard error though.
Pelase suggest
Code:
# iostat -En
c0t0d0 Soft Errors: 5 Hard Errors: 0 Transport Errors: 1
Vendor: TSSTcorp Product: CD/DVDW TS-L632D Revision: SI03 Serial No:
Size: 0.67GB <671088640 bytes>
Media Error: 0 Device Not Ready: 0 No Device: 0 Recoverable: 0
Illegal Request: 5 Predictive Failure Analysis: 0
c1t0d0 Soft Errors: 0 Hard Errors: 0 Transport Errors: 0
Vendor: FUJITSU Product: MAX3147NCSUN146G Revision: 1503 Serial No: 0729G03TAW
Size: 146.80GB <146800115712 bytes>
Media Error: 0 Device Not Ready: 0 No Device: 0 Recoverable: 0
Illegal Request: 0 Predictive Failure Analysis: 0
c1t1d0 Soft Errors: 0 Hard Errors: 0 Transport Errors: 0
Vendor: FUJITSU Product: MAX3147NCSUN146G Revision: 1503 Serial No: 0729G03T97
Size: 146.80GB <146800115712 bytes>
Media Error: 0 Device Not Ready: 0 No Device: 0 Recoverable: 0
Illegal Request: 0 Predictive Failure Analysis: 0
Thanks
Pradeep
Last edited by DukeNuke2; 06-03-2010 at 03:54 AM..
Hi All,
I have new Netra 240 box which is not detecting its harddisk equiped with itse same har disk are detected when I swap with another machine.
Same time If I swap hardisk of other machine to this Netra 240 box, also do not work. I have checked chassis, cabling etc and all looks fine. ... (1 Reply)
so i've grabbed this sun netra t1 for some small dev work. now obviously i need to install sol10. no problem done it a million times except for the fact that i've never actually done it w/o a term server. so i grab a usb to serial and a serial to rj45 (the one you get in every cisco order.. roll... (24 Replies)
Hi,
sunfire v240 and netra 240 are looks similar. system board, memory and processors are similar, then why netra 240 called as telco server?
can anyone tell the difference.
RJS (1 Reply)
Hello everyone,
I'm extremely new when it comes to SUN servers so bear with me and hopefully I can describe the issue I have accurately.
At work we just received a refurbished SUN Netra 240 server. I was told to change some of the EEprom settings, and to do that I was to use a... (0 Replies)
I am trying to use a serial communications device that is connected to /dev/ttyb on a netra 240 server. This is a solaris zone configuration using solaris 10 0910. I am able to access /dev/ttyb from the global zone but not throught he non-global zone. I have enabled all of the tty devices in my... (0 Replies)
Hi guys,
when I power on my sun netra 240 server,
it displays these error messages:
1. Notice: cpu 0 has 2048/2048 MB of memory disabled.
2. Error : The following devices are disabled dimm1.
Please can anyone be kind enough to explain this for me?
Thanks (2 Replies)
Hello all,
I recently powered on my Netra AX1105 server only to be greeted with the following error message. I am not sure what to do here,
I cant fun fsck on OK prompt.. did ok>boot -r and now it keeps booting from net, then I run ok>boot disk then outputs the following message... and keeps... (3 Replies)
Hi Guys,
Could someone please share the dvd/cd that came with server Netra x4200 M2 since it is not more available in Oracle site? Or do you know where I can get that?
Thanks! (4 Replies)
Hi,
One of my Netra 240 went into hung state and I had to reboot it. I powered it off and tried booting it again but unsuccessful. It is not connected to SAN and have local disks. Not able to boot in failsafe mode too.
There are two disks of 72GB, both are mirrored in SVM. It complains about... (5 Replies)
Discussion started by: solaris_1977
5 Replies
LEARN ABOUT CENTOS
poweroff
HALT(8) halt HALT(8)NAME
halt, poweroff, reboot - Halt, power-off or reboot the machine
SYNOPSIS
halt [OPTIONS...]
poweroff [OPTIONS...]
reboot [OPTIONS...]
DESCRIPTION
halt, poweroff, reboot may be used to halt, power-off or reboot the machine.
OPTIONS
The following options are understood:
--help
Prints a short help text and exits.
--halt
Halt the machine, regardless of which one of the three commands is invoked.
-p, --poweroff
Power-off the machine, regardless of which one of the three commands is invoked.
--reboot
Reboot the machine, regardless of which one of the three commands is invoked.
-f, --force
Force immediate halt, power-off, reboot. Do not contact the init system.
-w, --wtmp-only
Only write wtmp shutdown entry, do not actually halt, power-off, reboot.
-d, --no-wtmp
Do not write wtmp shutdown entry.
--no-wall
Do not send wall message before halt, power-off, reboot.
EXIT STATUS
On success, 0 is returned, a non-zero failure code otherwise.
NOTES
These are legacy commands available for compatibility only.
SEE ALSO systemd(1), systemctl(1), shutdown(8), wall(1)systemd 208HALT(8)