06-02-2010
Hi Reboot,
thanks for the info
10 More Discussions You Might Find Interesting
1. Solaris
Hello,
I am trying to do mirror in solaris 9. I have total 0-7 disks
4 5 6 7
0 1 2 3
Drive 0 and Drive 4 = Boot Drives
Need to Mirror following drives.
Drive 1 and Drive 5 = Need to mirror
Drive 1 was mounted on: /prod1, /prod2, /prod3, /prod4, /prod5.
Then i... (3 Replies)
Discussion started by: deal732
3 Replies
2. Solaris
Hi,
am a newbie at solaris. Need advice and help on this.
1) How do I break the mirror between 2 hard disks. (wish to keep 1 good hard disk as backup)
2) After remove 1 hard disk and put in new hard disk, how do I initialise or fomat the new hard disk?
3) How do I put back the backup... (3 Replies)
Discussion started by: chongkls77
3 Replies
3. Solaris
I have two 72GB disks that are mirrored and mounted (/backup). I have a 18GB drive in an array I just attached to the server, which is running Solaris 9.
I need to create a new logical volume partition and make the existing mirror device (/dev/md/dsk/d34) and the array's 18GB drive a member of... (3 Replies)
Discussion started by: dotcom75
3 Replies
4. Shell Programming and Scripting
Hi,
I have a question regarding finding free space on the disk of a solaris machine.
Many mount points are available in my machine. Right now i am using
df -b option to get the free disk space available.
I have an assignment to check free space on the disk.
I pass the directory as a... (3 Replies)
Discussion started by: raghu.amilineni
3 Replies
5. Solaris
Hi everyone,
Normally it always easier in Sparc machine, i can set or manually use the boot-device in NVram to boot the mirrored disk. However I have a big trouble about x86 mirror for a long time. I have been doing anything i can: search document, google, ask the others.
Recently i did as... (5 Replies)
Discussion started by: tien86
5 Replies
6. Solaris
Hello:
I have a machine built on 2 drives and mirrors have been created to a second set of 2 drives (4 total) on the same platform. SVM.
Might anyone provide guidance to create a second machine by breaking the mirrored set, moving the two mirrors (2) to another machine (same platform type),... (1 Reply)
Discussion started by: 4dailyrunner
1 Replies
7. Solaris
I’m setting up a boot disk mirror on Solaris 10 x86. I’m used to doing it on SPARC, where you can copy the partition table using fmthard. My x86 boot disk has 2 primary partitions, a Solaris one and a diagnostic one. Is there a way to copy those 2 primary partitions to the second disk without... (6 Replies)
Discussion started by: TKD
6 Replies
8. Solaris
hi friends, need help.. it is my first time patching using mirror disk backup approach, not so sure about the steps :confused: how do you detach, patch it, boot it and reattach it ? any kind soul here can advise ? thanks in advance..:)
below is the information from my machine:
Filesystem ... (3 Replies)
Discussion started by: Exposure
3 Replies
9. HP-UX
what is the difference between DRD and Root Mirror Disk using LVM mirror ? (3 Replies)
Discussion started by: maxim42
3 Replies
10. Solaris
We have Proliant DL380 G2 running Solaris 9 x86
There are 6 physical disks installed which I believe are mirrored at hardware level to 3 sets to present 3 disks to the OS.
Is there any way to check the mirror status at OS level ?
I am guessing not and it may need a trip to site as we have no... (4 Replies)
Discussion started by: frustrated1
4 Replies
LEARN ABOUT ULTRIX
doconfig
doconfig(8) System Manager's Manual doconfig(8)
Name
doconfig - a program to aid system configuration
Syntax
/etc/doconfig [-c config_file] [-e ed_script]
Description
The shell script modifies a copy of the GENERIC configuration file for a new ULTRIX system kernel. The script prompts you for the system
name. If the system name does not currently exist, a system configuration file with that system name is built.
Whether the configuration file is built or not, the script then allows you to edit, configure, and build until both the configuration and
the kernel build run without errors. Additional runs of can be made to tune the configuration further.
When new hardware is added to a system, the configuration file should be updated to reflect the new system configuration. When updating an
existing configuration file or creating a new configuration file with the system must be operating the generic kernel or new hardware may
not be found. To successfully complete the process, follow these steps:
1. Save the running as
2. Move to
3. Reboot the system to single user mode.
4. Check file systems.
5. Mount the file system.
6. Run the program. (When execution is complete, make a note of the message prints showing the path and location of the new
7. Move to
8. Copy the new (from the message noted above) to
9. Reboot the system.
Options
-c The name of the existing configuration file should be supplied without specifying the pathname. This file should exist in the
directory. A new kernel is built using the specified configuration file.
-e When specified, the configuration file is edited by the ed script before building the new kernel.
Files
See Also
ed(1), config(8)
Basic Installation Guide
Guide to System Configuration File Maintenance
RISC doconfig(8)