How to initialize tape drive Post: 302425216

8 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Tape drive install

I'm trying to install a tape drive on a compaq SCO OS 505. well I have gone through the mkdev tape comands and what have you yet no luck. when I reboot and do a simple tape rewind it gives me an error no such device etc.etc. IS there a diference in the xct0 and rct0 a the default? help..

2. Linux

Installing tape drive?

Hello. I have Redhat 8.0 on a laptop. Working good. I wanted to install the tape drive that is physically attached to it. The tape drive worked fine under Windows98SE. It's one of those parallel QIC-80 drives and I confirmed that it is supported by FTape. It appears that FTape might already...

3. UNIX for Dummies Questions & Answers

tape drive

Hi, I need to restore my tape backup, when I type "tape status" it gives; status : ready beginning-of-tape write-protected soft errors : 0 hard errors : 0 underruns : 3 but...

4. AIX

Tape Drive

I have tape drive in one Lpar. when i saw that time tape is in defined state. After that i deleted the tape drive using the rmdev -R command. Then fired the cfgmgr -v command. But I am not getting the tape drive. Now the drive is even not in defined state also. It is not shown the tape drive. How...

5. Solaris

Help with tape drive

Hey folks, Linux admin here, forced to use Opensolaris to try to use ufsdump/ufsrestore to get some data of some old tapes. I've got Opensolaris 2009.06 on x86 and a Sony SDX-700V. As a "control" experiment, I booted the system with a Linux live CD and the tape drive worked perfectly. ...

6. UNIX for Dummies Questions & Answers

Using a remote tape drive.

Hello everyone. I googled a little bit, and the best anwers i had were found in this forum. But , unfortunately, they couldn't give me a solution. So i decided to ask the question completely. I have two servers: One RHEL 5 , x64 , with a SCSI DAT72 Tape Drive. Another (the new one), with...

7. Solaris

[SOLVED] How to initialize LTO5 Tape Drive?

Hi, We replaced one of our tape drives (attached to a SPARC Server) with an LTO5 one (external, attached vi SAS). Manually we check (using tar) that the OS can write data to the Tape Drive, however, the application backup is failing. Since the application takes its own backup, the apps team...

8. HP-UX

TAPE drive

I have used ioscan -fnC tape and the system identified the tape drive. what is the command to show a listing of what is on the tape? I have used ls /dev/rmt/rmt0 to no avail. can anyone help? Thanks in advance

LEARN ABOUT REDHAT

tapeinfo

TAPEINFO(1)						      General Commands Manual						       TAPEINFO(1)

NAME

       tapeinfo - report SCSI tape device info

SYNOPSIS

       tapeinfo -f <scsi-generic-device>

DESCRIPTION

       The  tapeinfo  command  reads  various information from SCSI tape drives that is not generally available via most vendors' tape drivers. It
       issues raw commands directly to the tape drive, using either the  operating  system's  SCSI  generic  device  (	e.g.  /dev/sg0	on  Linux,
       /dev/pass0 on FreeBSD) or the raw SCSI I/O ioctl on a tape device on some operating systems.

       One  good  time	to  use 'tapeinfo' is immediately after a tape i/o operation has failed. On tape drives that support HP's 'tapealert' API,
       'tapeinfo' will report a more exact description of what went wrong.

       Do be aware that 'tapeinfo' is not a substitute for your operating system's own 'mt' or similar tape driver control program. It is intended
       to supplement, not replace, programs like 'mt' that access your operating system's tape driver in order to report or set information.

OPTIONS

       The first argument, given following -f , is the SCSI generic device corresponding to your tape drive.  Consult your operating system's doc-
       umentation for more information (for example, under Linux these are generally start at /dev/sg0 under FreeBSD these start at /dev/pass0).

       Under FreeBSD, 'camcontrol devlist' will tell you what SCSI devices you have, along with which 'pass' device controls  them.  Under  Linux,
       "cat /proc/scsi/scsi" will tell you what SCSI devices you have.

BUGS AND LIMITATIONS

       This program has only been tested on Linux with a limited number of tape drives (HP DDS4, Seagate AIT).

AVAILABILITY

       tapeinfo  is  currently being maintained by Eric Lee Green <eric@badtux.org> formerly of Enhanced Software Technologies Inc. The 'mtx' home
       page is http://mtx.sourceforge.net and the actual code is currently available there and via CVS from http://sourceforge.net/projects/mtx/ .

SEE ALSO

       mt(1),mtx(1),scsitape(1)

								    TAPEINFO1.0 						       TAPEINFO(1)