I need to replace the line containing "STAGE_DB" with the line
"STAGE_DB $DB # database that contains the table being loaded ($workingDB)"
Here $DB is passed during the runtime.
How can I do this?
Thanks,
Kousikan (2 Replies)
Please help!
Input pattern, where ... could be any number of lines
struct A {
Blah1
Blah2
Blah3
...
} B;
output pattern
struct AB {
Blah1
Blah2
Blah3
...
};
I need help in extracting everything between { and }
if it would have been on a single line { \(.*\)} should have worked. (15 Replies)
I am searching a dhcpd.conf to find the hardware ethernet match, then once the match is found delete just the line above it. For example:
testmachine.example {
hardware ethernet 00:00:00:00:00:00;
fixed address 192.168.1.100;
next-server 192.168.1.101;
filename "linux-install/pxelinux.0";
}... (3 Replies)
the following range matching works great but i wish to add a blank line after each range result set... which i've tried and researched to no avail
MY INPUT DATA:
CURRENT CODE I'M USING:
sed -n '/*$/,/;/p' $INPUT_FILE
RESULTS I'M GETTING:
RESULT I looking to... (5 Replies)
New to sed...
Have a file foo.txt (below).
Need to replace text on 2 lines, but can only feed sed the first few characters of each line (all lines are unique).
So, in my example, I have put '$' in place of what I need to figure out how to feed the whole line.
What I have thus far:
sed -e... (6 Replies)
Hi,
I want to match a line which exists in a file. I have written a test script similar to below -
The content of the file file.txt would be like this -
/usr/bin/1234.xcf
/usr/bin/3456.xcf
/usr/bin/7897.xcf
/usr/bin/2345.xcf
out=`sed -n '\/usr\/bin\/7897.xcf/p' file.txt 2>&1`... (3 Replies)
Hi all,
This is my first post, so please go easy if I broke some rules. Not accustomed to posting in forums... :)
I'm looking for help on pattern matching within a multiline block and looking to highlight blocks/block-ids that do NOT contain a particular pattern.
For example an input file... (5 Replies)
Hi How Are you?
I am doing fine!
I need to go now?
I will see you tomorrow!
Basically I need to replace the entire line containing "doing" with a blank line:
I need to the following output:
Hi How Are you?
I need to go now?
I will see you tomorrow!
Thanks in advance.... (1 Reply)
awk , sed Experts,
I want to remove first and last line after pattern match "vg" :
I am trying : # sed '1d;$d' works fine , but where the last line is not having vg entry it is deleting one line of data.
- So it should check for the pattern vg if present , then it should delete the line ,... (5 Replies)
IRSEND(1) FSF IRSEND(1)NAME
irsend - basic LIRC program to send infra-red commands
SYNOPSIS
irsend [options] DIRECTIVE REMOTE CODE [CODE...]
DESCRIPTION
Asks the lircd daemon to send one or more CIR (Consumer Infra-Red) commands. This is intended for remote control of electronic devices such
as TV boxes, HiFi sets, etc.
DIRECTIVE can be:
SEND_ONCE - send CODE [CODE ...] once
SEND_START - start repeating CODE
SEND_STOP - stop repeating CODE
LIST - list configured remote items
SET_TRANSMITTERS - set transmitters NUM [NUM ...]
SIMULATE - simulate IR event
REMOTE is the name of a remote, as described in the lircd configuration file.
CODE is the name of a remote control key of REMOTE, as it appears in the lircd configuration file.
NUM is the transmitter number of the hardware device.
For the LIST DIRECTIVE, REMOTE and/or CODE can be empty:
LIST "" "" - list all configured remote names
LIST REMOTE "" - list all codes of REMOTE
LIST REMOTE CODE - list only CODE of REMOTE
The SIMULATE command only works if it has been explicitly enabled in lircd.
-h --help
display usage summary
-v --version
display version
-d --device
use given lircd socket [/var/run/lirc/lircd]
-a --address=host[:port]
connect to lircd at this address
-# --count=n
send command n times
EXAMPLES
irsend LIST DenonTuner ""
irsend SEND_ONCE DenonTuner PROG-SCAN
irsend SEND_ONCE OnkyoAmpli VOL-UP VOL-UP VOL-UP VOL-UP
irsend SEND_START OnkyoAmpli VOL-DOWN ; sleep 3
irsend SEND_STOP OnkyoAmpli VOL-DOWN
irsend SET_TRANSMITTERS 1
irsend SET_TRANSMITTERS 1 3 4
irsend SIMULATE "0000000000000476 00 OK TECHNISAT_ST3004S"
FILES
/etc/lirc/lircd.conf
Default lircd configuration file. It should contain all the remotes, their infra-red codes and the corresponding timing and wave-
form details.
DIAGNOSTICS
If lircd is not running (or /var/run/lirc/lircd lacks write permissions) irsend aborts with the following diagnostics:
"irsend: could not connect to socket"
"irsend: Connection refused" (or "Permission denied").
SEE ALSO
The documentation for lirc is maintained as html pages. They are located under html/ in the documentation directory.
lircd(8), mode2(1), smode2(1), xmode2(1), irrecord(1), irw(1), http://www.lirc.org.
irsend 0.8.7pre1 May 2010 IRSEND(1)