Hi,
I'm trying to write a script that reads filenames from a file and use these filenames in a loop. The filenames are all on one line and the problem is that these filenames have wildcards like * and braces like in them.
Right now what I'm doing is something like this:
echo "reading from... (0 Replies)
Hi,
I have prepared a config file in which I am declaring the value for a country such as: COUNTRY=USA
Now I am trying to read the country from the config file and print a message based on the same. I have written the following code in a script and when executing the script I getting an error.
... (14 Replies)
Hi,
In a script i am having trouble joining a variable to a file. for, example I read input from user as a variable a or b or c or d etc and want to join those to different files...
or
if user press a then it will open somefile.txt
if user press b then it will open otherfile.txt
any idea (4 Replies)
i get a name from user first name : last name, in this format. Now i am saving this to a file. what i want is, I do not want to save any name if I already have one entry o that same name..what should i do
for example
user give robert fernandez
this will save in file as robert:fernandez.
if... (5 Replies)
Hi All,
I am trying to read a .csv file which has some 6 columns.
Eg: samp.csv
one, two, three, four
six, seven, eight, nine
I used the following code,
for line in `cat samp.csv`
do
echo "$line"
done
It displays every comma seperated values in each line like,
one,... (1 Reply)
Hello C specialists,
I'm trying to write a program to read out a binary configuration file produced by a router.
But the output of Name and Value is cryptic. What's going wrong?
The structure of the binary file is very simple:
struct nvram_tuple {
char *name;
char *value;
... (5 Replies)
I've a file in linux with following text:
;ip address hostname put-location alt-put-location tftpserver
192.168.1.1 r01-lab1-net /mnt/nas1/fgbu/ /opt/fgbu/devicebackup 192.168.1.254Now I want to read these values and assign them to particular variables... (6 Replies)
Hello, I have a file in the following format
id sample platform R1 R2 gene1 gene2 gene3
1 abc llumina R1_001.fastq.gz R2_001.fastq.gz apoe prnpp asp
2 def llumina R1_001.fastq.gz R2_001.fastq.gz apoe prnpp
3 ghi llumina ... (3 Replies)
Hi,
I downloaded source code file from The GNU website and changed the source code of ls.c file, added printf command to it. It worked fine. Then, I deleted the printf command, saved the file and ran the command 'make sudo && make install' closed the terminal and printf statement went away.
I... (1 Reply)
Discussion started by: akanksha1509
1 Replies
LEARN ABOUT HPUX
xmtablist
XmTabList(library call) XmTabList(library call)
NAME
XmTabList -- Data type for a tab list
SYNOPSIS
#include <Xm/Xm.h>
XmTabList
DESCRIPTION
XmTabList is the data type for a tab list. A tab list consists of tab stop list entries (XmTabs). Whenever a tab component is encountered
while an XmString is being rendered, the origin of the next X draw depends on the next XmTab. If a tab stop would cause text to overlap,
the x position for the segment is reset to follow immediately after the end of the previous segment.
Tab lists are specified in resource files with the following syntax:
resource_spec: tab WHITESPACE [, WHITESPACE tab ]*
The resource value string consists of one or more tabs separated by commas. Each tab identifies the value of the tab, the unit type, and
whether the offset is relative or absolute. For example:
tab := float [ WHITESPACE units ]
float := [ sign ] [[ DIGIT]*. ]DIGIT+
sign := +
where the presence or absence of sign indicates, respectively, a relative offset or an absolute offset. Note that negative tab values are
not allowed. units indicates the unitType to use as described in the XmConvertUnits reference page.
For example, the following specifies a tab list consisting of a one inch absolute tab followed by a one inch relative tab:
*tabList: 1in, +1in
For resources of type, dimension, or position, you can specify units as described in the XmNunitType resource of the XmGadget, XmManager,
or XmPrimitive reference page.
RELATED
Refer to the Motif Programmer's Guide for more information about tabs and tab lists. XmTabListCopy(3), XmTabListFree(3), XmTabListGet-
Tab(3), XmTabListInsertTabs(3), XmTabListRemoveTabs(3), XmTabListReplacePositions(3), and XmTabListTabCount(3).
XmTabList(library call)