Hello,
Iam having problems getting more then one ip to work here is my setup!
Hostname: nexus
NIC: e000g1
(example ips)
My ips 80.80.80.15 to 80.80.80.20
Defaultrouter 80.80.80.1
nameservers 80.80.80.100 and 80.80.80.200
How would i do this? Any help would be mutch appriciated!... (7 Replies)
Hi All, :(:confused:
I have scoured the web and can't find this anywhere.
What I am trying to do is set up a static route through an available gateway on a server, and then test connectivity through TELNET.
I have done this on AIX (I already had this procedure).
On AIX I would use SMIT. ... (7 Replies)
Hi,
how to assign the rights(admin,..) to groups .
I can create group using groupadd.
but i don't know how to assign rights and adding members
please tell me how to do that
Thank you (2 Replies)
I m having interface ce0 ce1 and its sub interfaces for that.
I want to give MAC addresses for the same.
How will I assign it.
Please give solution for the same (4 Replies)
hello, i need help on setting my coyote linux, i've working on this for last 5 days, can't get it to work. I've been posting this message to coyote forum, and other linux forum, but haven't get any answer yet. Hope someone here can help me...... please see my attached picture first.
... (0 Replies)
Hi All
I am having a solaris 10 virtual machine on vista (using vmware 7) laptop.
Now i want to access virtual machine from vista using putty.
Problem is that i insalled the solaris machine as dhcp. and whenever i connect to internet or reboot my system the IP address of solaris... (1 Reply)
hi,
how to assign static ip address to the server having solaris 10. assign static ip to nge0 which will sustain across reboots which will include all settings including gateway setting etc.. (2 Replies)
I'm writing a program which uses curl to be run on Linux PCs which will be used by a number of different users. I cannot make the users all install curl on their individual machines, so I have tried to link curl in statically, rather than using libcurl.so. I downloaded the source and created a... (8 Replies)
I have installed Solaris 11.2 in VMware Player, networked in bridged mode. When Solaris uses DHCP everything is OK, I can reach internet, as well as other systems on my LAN. When I switch to static, I have connections to my LAN, but can not get to internet, the DNS resolution is somehow not... (2 Replies)
We have 2 solaris 10 t5240 servers with static IP addresses on nxge0 I/F which were rebooted a few days back with a known good config that has been in place for years (for /etc/hosts, /etc/hostname.nxge0, /etc/netmasks, etc)
They are not using dhcp.
About the same time today, both of their... (7 Replies)
Discussion started by: hdatontodo
7 Replies
LEARN ABOUT SUNOS
sys-unconfig
sys-unconfig(1M) System Administration Commands sys-unconfig(1M)NAME
sys-unconfig - undo a system's configuration
SYNOPSIS
/usr/sbin/sys-unconfig
DESCRIPTION
The sys-unconfig command is used to restore a system's configuration to an "as-manufactured" state, ready to be reconfigured again. The
system's configuration consists of hostname, Network Information Service (NIS) domain name, timezone, IP address, IP subnet mask, and root
password. This operation is the inverse of those performed by the sysidnet(1M), sysidns(1M), and sysidsys(1M) programs run at boot. See
sysidtool(1M).
sys-unconfig does the following:
o Saves current /etc/inet/hosts file information in /etc/inet/hosts.saved.
o If the current /etc/vfstab file contains NFS mount entries, saves the /etc/vfstab file to /etc/vfstab.orig.
o Restores the default /etc/inet/hosts file.
o Removes the default hostname in /etc/hostname.interface files for all interfaces configured when this command is run. To determine
which interfaces are configured, run the command 'ifconfig-a'. The /etc/hostname.interface files corresponding to all of the inter-
faces listed in the resulting output, with the exception of the loopback interface (lo0), will be removed.
o Removes the default domainname in /etc/defaultdomain.
o Restores the timezone to PST8PDT in /etc/TIMEZONE.
o Disables the Network Information Service (NIS) and Network Information Service Plus (NIS+) if either NIS or NIS+ was configured.
o Removes the file /etc/inet/netmasks.
o Removes the file /etc/defaultrouter.
o Removes the password set for root in /etc/shadow.
o Removes the file /etc/.rootkey.
o Executes all system configuration applications. These applications are defined by prior executions of a sysidconfig -a application.
(See sysidconfig(1M)). When sys-unconfig is run, all system configuration applications are passed one argument, -u.
o Removes the file /etc/resolv.conf.
o Disables LDAP by removing /var/ldap/ldap_client_cache, /var/ldap/ldap_client_file, /var/ldap/ldap_client_cred, and
/var/ldap/cachemgr.log.
o Regenerates keys for sshd(1M).
When sys-unconfig is finished, it performs a system shutdown. sys-unconfig is a potentially dangerous utility and can only be run by the
super user.
FILES
/etc/default/init process control initialization
/etc/defaultdomain
/etc/defaultrouter
/etc/hostname.interface
/etc/inet/hosts host name database
/etc/inet/netmasks network mask database
/etc/nodename
/etc/.rootkey super-user's secret key
/etc/shadow shadow password file
/etc/vfstab virtual file system table
/var/nis/NIS_COLD_START
/var/yp/binding/*/ypservers
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWadmap |
+-----------------------------+-----------------------------+
SEE ALSO init(1M), kdmconfig(1M), sshd(1M), sysidconfig(1M), sysidtool(1M), hosts(4), netmasks(4), shadow(4), attributes(5)NOTES
sys-unconfig is not available on diskless clients.
SunOS 5.10 4 Jun 2004 sys-unconfig(1M)