05-12-2010
Solaris - Assign Static IP
Hi,
I have cloned a SOLARIS 8 (BLADE 150) Hard Disk and have put into other system. So, now how do I configure the NIC and assign static IP for this new machine ?
10 More Discussions You Might Find Interesting
1. Solaris
Hello,
Iam having problems getting more then one ip to work here is my setup!
Hostname: nexus
NIC: e000g1
(example ips)
My ips 80.80.80.15 to 80.80.80.20
Defaultrouter 80.80.80.1
nameservers 80.80.80.100 and 80.80.80.200
How would i do this? Any help would be mutch appriciated!... (7 Replies)
Discussion started by: empty
7 Replies
2. Solaris
Hi All, :(:confused:
I have scoured the web and can't find this anywhere.
What I am trying to do is set up a static route through an available gateway on a server, and then test connectivity through TELNET.
I have done this on AIX (I already had this procedure).
On AIX I would use SMIT. ... (7 Replies)
Discussion started by: jeffpas
7 Replies
3. Solaris
Hi,
how to assign the rights(admin,..) to groups .
I can create group using groupadd.
but i don't know how to assign rights and adding members
please tell me how to do that
Thank you (2 Replies)
Discussion started by: S_venkatesh
2 Replies
4. Solaris
I m having interface ce0 ce1 and its sub interfaces for that.
I want to give MAC addresses for the same.
How will I assign it.
Please give solution for the same (4 Replies)
Discussion started by: sunray
4 Replies
5. IP Networking
hello, i need help on setting my coyote linux, i've working on this for last 5 days, can't get it to work. I've been posting this message to coyote forum, and other linux forum, but haven't get any answer yet. Hope someone here can help me...... please see my attached picture first.
... (0 Replies)
Discussion started by: dlwoaud
0 Replies
6. UNIX for Dummies Questions & Answers
Hi All
I am having a solaris 10 virtual machine on vista (using vmware 7) laptop.
Now i want to access virtual machine from vista using putty.
Problem is that i insalled the solaris machine as dhcp. and whenever i connect to internet or reboot my system the IP address of solaris... (1 Reply)
Discussion started by: ankurk
1 Replies
7. Solaris
hi,
how to assign static ip address to the server having solaris 10. assign static ip to nge0 which will sustain across reboots which will include all settings including gateway setting etc.. (2 Replies)
Discussion started by: pankajd
2 Replies
8. Programming
I'm writing a program which uses curl to be run on Linux PCs which will be used by a number of different users. I cannot make the users all install curl on their individual machines, so I have tried to link curl in statically, rather than using libcurl.so. I downloaded the source and created a... (8 Replies)
Discussion started by: BrandonShw
8 Replies
9. Solaris
I have installed Solaris 11.2 in VMware Player, networked in bridged mode. When Solaris uses DHCP everything is OK, I can reach internet, as well as other systems on my LAN. When I switch to static, I have connections to my LAN, but can not get to internet, the DNS resolution is somehow not... (2 Replies)
Discussion started by: migurus
2 Replies
10. Solaris
We have 2 solaris 10 t5240 servers with static IP addresses on nxge0 I/F which were rebooted a few days back with a known good config that has been in place for years (for /etc/hosts, /etc/hostname.nxge0, /etc/netmasks, etc)
They are not using dhcp.
About the same time today, both of their... (7 Replies)
Discussion started by: hdatontodo
7 Replies
dms(8) System Manager's Manual dms(8)
Name
dms - diskless management services utility
Syntax
/etc/dms
Description
The utility performs diskless management services. You can use to install products into diskless management services areas on a server
machine and register diskless clients so that they can access those products on the server machine, rather than having each client install
the products to a disk on its local machine. The server machine can be either a VAX or a RISC machine and it can serve both VAX and RISC
clients.
Before you set up a diskless management services area on a server, the following software should be installed: Local Area Network (LAN);
Network File System (NFS); and Maintenance Operations Protocol (MOP).
The utility performs the following functions:
a - Add Client Processor
m - Modify Client Parameters
r - Remove Client Processor
l - List Registered Clients
s - Show Products in Diskless Environments
i - Install Software
c - Create Diskless Area on Disk
k - Kernel Rebuild or Copy
To set up a diskless management services area on a server, select functions in the following order:
1. Create Diskless Area on Disk (c)
This sets up the disk partitions needed for the two diskless management services file systems, and (The question mark (?) represents
a unique number assigned by The file system contains a common root area that is copied to each client when it is registered, and a
area that is shared by all the clients. The file system contains a copy of the common root area for each registered diskless
client.
2. Install Software (i)
This installs the products from the distribution media to the file system. If the product will be accessed by VAX clients, the
images from the media are put under a directory under the file system. If the product will be accessed by RISC clients, the images
from the media will be put under a directory under the file system. The question mark (?) represents a unique number assigned by
To register a diskless client, select the Add Client Processor option (a). This copies the common root area in the file system, for exam-
ple, to the diskless client's directory in the file system, for example, The server's file is updated to allow the client to access its
individual root and the shared area.
Each diskless client's area also contains a client parameter file,
You must use interactively to set up a diskless environment or to modify client parameters.
There are several functions you can use either interactively or from the command line:
- Add Client Processor
- Show Products in Diskless Environments
- Remove Client Processor
- Kernel Rebuild
When the first diskless client is registered for a diskless management services area, a database file, is created on the server machine.
You can use this file and the command line to manage groups of diskless clients.
Files
See Also
exports(5nfs), addnode(8), setld(8)
Guide to Diskless Management Services
Guide to Server Setup
dms(8)