05-10-2010
Thanks so much for the guidance, guys. I will give both a shot and let you know how it goes. Ideally, I want the data to be parsed and written in real time without a buffer, although I did consider going that route.
6 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
hi all :confused:
i am wondering if there is a way to convert from EPOCH time to the standard tim, may be using a script or some thing else???????
thanks............................ (5 Replies)
Discussion started by: TheEngineer
5 Replies
2. Solaris
Hi friends,
I am new to solaris and looking for a job, when ever i attend interview i get most of the questions on real time problems, every one sak me the same questions what are the problems you face daily.. and what are the types?
i know few like, disk extension,swap memory increasing,... (2 Replies)
Discussion started by: kurva
2 Replies
3. Shell Programming and Scripting
Dear experts,
I have an epoch time input file such as : -
1302451209564
1302483698948
1302485231072
1302490805383
1302519244700
1302492787481
1302505299145
1302506557022
1302532112140
1302501033105
1302511536485
1302512669550
I need the epoch time above to be converted into real... (4 Replies)
Discussion started by: aismann
4 Replies
4. UNIX for Dummies Questions & Answers
Hi
Not sure if this can be achieved by unix , but still would like to know if there is any way by which I can do the below given logic
cat sam1 > out1
cat sam2 > out2
when either one of this finished the the next file shd be written in that file, meaning
cat sam3 >> out1/out2... (2 Replies)
Discussion started by: Sri3001
2 Replies
5. Shell Programming and Scripting
Hello,
I searched the forum and found the parsing iostat data in real time but that does not help me. What I would like to do is to parse the iostat data that has been gathered. Below is an example of the iostat output:
System configuration: lcpu=4 drives=5 ent=0.10 paths=20 vdisks=2
... (11 Replies)
Discussion started by: tommyd
11 Replies
6. Shell Programming and Scripting
# date +%s -d "Mon Feb 11 02:26:04"
1360567564
# perl -e 'print scalar localtime(1360567564), "\n";'
Mon Feb 11 02:26:04 2013
the epoch conversion is working fine. but one of my application needs 13 digit epoch time as input
1359453135154
rather than 10 digit epoch time 1360567564... (3 Replies)
Discussion started by: vivek d r
3 Replies
time(1) General Commands Manual time(1)
Name
time - time a command
Syntax
time command
/bin/time command
Description
The command lets the specified command execute and then outputs the amount of elapsed real time, the time spent in the operating system,
and the time spent in execution of the command. Times are reported in seconds and are written to standard error.
If you are using any shell except the C shell, you can give the command as shown on the first line of the Syntax section. If you are using
the C shell, you must use the command's full pathname as shown on the second line of the Syntax section. If you do not use the full path-
name, will execute its own built-in command that supplies additional information and uses a different output format.
The command can be used to cause a command to be timed no matter how much CPU time it takes. For example:
% /bin/time cp /etc/rc /usr/bill/rc
0.1 real 0.0 user 0.0 sys
% /bin/time nroff sample1 > sample1.nroff
3.6 real 2.4 user 1.2 sys
This example indicates that the command used negligible amounts of user and system time and had an elapsed time of 1/10 second (0.1). The
command used 2.4 seconds of user time and 1.2 seconds of system time, and required 3.6 seconds of elapsed time.
Restrictions
Times are measured to an accuracy of 1/10 second. Thus, the sum of the user and system times can be larger than the elapsed time.
See Also
csh(1)
time(1)