Note 1: If you have the frame buffer Raptor GFXP -04 REV 50
(part 370-3753-04), you *must* install patch 110126-03 to upgrade the
FCode in the card **BEFORE** you can do the firmware update. Revisions -05 and up of the frame buffer are not affected.
Failure to install the frame buffer patch (110126-03) will cause
"FATAL" resets after the firmware update.
I know I have a Raptor PGX32 frame buffer, is there a way to know what version of the frame buffer FCode I have? Do I need to apply the moentioned patch?
hi,
i hv received SUNfire 280R system ........for its initial configuration i want to connect to it through hyperterminal from the windows system..........i hv got one serial port to RJ-45 port converter with the system............can anybody tell me the normal console cable which is used to... (3 Replies)
Greetings all,
I'm in a bit of a situation. I have this Sunfire 280R system that did not have a floppy drive in it, yet we needed one. We grabbed one from another Sun box we had laying around unused, and installed it. The system couldnt recognize it. Tried another floppy drive (non-sun) and... (4 Replies)
Hi there
Does anybody know what the biggest capacity disk I can get into a Sunfire 280R
I currently have two 73gb disks , but I need to get these up to the biggest available
Any help would be greatly appreciated (4 Replies)
Hi,
We had a disk go bad in this SunFire 280R, running Solaris 8 - Generic_117350-46. We replaced the disk and partitioned it. We metadetached all the metadevices but for some reason the new disk is showing up in the metadb as Concat/Stripe and it won't let us re-sync the mirror. We are not... (2 Replies)
Hi,
I have to question:
1) when O/S is booting, i see messages:
/dev/rdsk/c1t0d0s5: is logging
/dev/rdsk/c1t0d0s3: is logging
/dev/rdsk/c1t0d0s7: is logging
i partitioned these slices during installation of O/S 5.9. I can access to these mountpoint no problem. But... (3 Replies)
hi,
i just completed installing O/S 5.9 on Sunfire 280R with O/S 5.9. During installation, i wasn't able to add IP, Default gateway, NDS and netmask because the lan port wasn't not active yet. Now that i have a lan port active, how to add network components onto the system?
I did ifconfig to... (1 Reply)
Hi,
i just finished installing solaris 5.9 and I'm looking for the tools to tell me if i should update the patches or how to make sure that the current patches are ok?
thanks (2 Replies)
Hi,
I' trying to install O/S 5.9 on Sparc system Sunfire 280R. I downloaded CD install and CD 2 from Sun Website but later i dowloaded CD 2 that i forgot for my installation. All CD are in ISO formats.
I boot system at OK prompt then issue
OK boot cdrom
when it asks for CD 1, i removed... (7 Replies)
I got the system couple of days back from one of my friend. Last night I turned it on and I noticed that maintenance LED is on. At the same time I added an LCD monitor via VGA and nothing was showing on the screen. Though the system does not have any HDD So not sure if system will even show a BIOS... (3 Replies)
Discussion started by: pgirish007
3 Replies
LEARN ABOUT CENTOS
glxgetvisualfromfbconfig
GLXGETVISUALFROMFBCO(3G) OpenGL Manual GLXGETVISUALFROMFBCO(3G)NAME
glXGetVisualFromFBConfig - return visual that is associated with the frame buffer configuration
C SPECIFICATION
XVisualInfo * glXGetVisualFromFBConfig(Display * dpy, GLXFBConfig config);
PARAMETERS
dpy
Specifies the connection to the X server.
config
Specifies the GLX frame buffer configuration.
DESCRIPTION
If config is a valid GLX frame buffer configuration and it has an associated X Visual, then information describing that visual is returned;
otherwise NULL is returned. Use XFree to free the data returned.
NOTES
glXGetVisualFromFBConfig is available only if the GLX version is 1.3 or greater.
If the GLX version is 1.1 or 1.0, the GL version must be 1.0. If the GLX version is 1.2, then the GL version must be 1.1. If the GLX
version is 1.3, then the GL version must be 1.2.
XVisualInfo is defined in Xutil.h. It is a structure that includes visual, visualID, screen, and depth elements.
ERRORS
Returns NULL if config is not a valid GLXFBConfig.
SEE ALSO
glXGetFBConfigAttrib(), glXChooseFBConfig(), glXChooseVisual(), glXGetConfig()
COPYRIGHT
Copyright (C) 1991-2006 Silicon Graphics, Inc. This document is licensed under the SGI Free Software B License. For details, see
http://oss.sgi.com/projects/FreeB/.
AUTHORS
opengl.org
opengl.org 06/10/2014 GLXGETVISUALFROMFBCO(3G)