Hi all
I am working on MSR110 ...Can anyone plz tell me how to use the configuration commands with magnetic reader???. Please help me out as i have to develop API in C on linux platform.MSR110 is not responding to the configuration commands.
Please help...
Regards
Mahima (0 Replies)
Hi all.
A friend of mine just recently gave me an old RISC 6000 machine to learn on for my AIX certification. I installed AIX 4.3.3 and everything seems to work fine, except there are no man pages. Is there a way to generate man pages on this machine?
Thanks alot in advance. (5 Replies)
I am new to program development on Linux.
I wonder what computer languages are easy to grasp to create man - machine interactive interface software, which can accept inputs (parameters) from usrers, and present (display) the calculation results to users.
Before, I have heared about Perl,... (10 Replies)
Hi,
Is there are any special preocedure for extending veritas mirror-stripe volume? In my case , volume lay out looks as below
v test - ENABLED ACTIVE 419430400 SELECT - fsgen
pl test-01 test ENABLED ACTIVE 419454720 STRIPE 3/128 RW
sd... (0 Replies)
I have a PERC 5/i card. Im using with it 3 15k rpm HDD's (model: SEAGATE Savvio 15K ST936751SS). Im going to install debian on this array.. and im looking for performance... So what would be the stripe size that i should set this raid 0 into to give me the best performance?
Thanks (22 Replies)
Hello all.
I have a volume group with 8 PV's, and a logical volume striped across these 8 volumes.
However, an lslv is showing:
STRIPE WIDTH: 9
STRIPE SIZE: 64k
There's really only eight disks, so how can the stripe width be 9?
ODM also showed this:
# odmget CuAt |... (4 Replies)
Hello,
Linux man command search is case insensitive by default, but not AIX man.
How do I serch case insensitive while using AIX manual pages ?
thanks
Vilius (7 Replies)
Hello Admins..
I am going through solaris volume manager guide for RAID-0 concatenation and stripes, I do not understand the concept of stripe from following example of concatenation.
There is an eample for concatenation:
# metainit d25 1 1 c0t1d0s2
d25: Concat/Stripe is setup
the... (5 Replies)
Discussion started by: snchaudhari2
5 Replies
LEARN ABOUT ULTRIX
scsi
SCSI(4) Kernel Interfaces Manual SCSI(4)Name
SCSI - Small Computer System Interconnect
Description
The ULTRIX system interfaces to disk and tape devices through the Small Computer System Interconnect (SCSI). Initial ULTRIX SCSI support
is limited to the Digital-supplied mass storage devices. The following devices are fully supported on the ULTRIX system:
o Winchester disks: RZ22, RZ23, RZ23L, RZ24, RZ55, RZ56, RZ57, RX23, RX26, RX33
o Magnetic tapes: TZ30, TZK50, TLZ04, TSZ05, TKZ08, TZK10
o Optical disks: RRD40, RRD42
Under the ULTRIX operating system, a SCSI device is referred to by its logical name. Logical names take the following form:
nn#
The nn argument is the two-character name; the number sign (#) represents the unit number. The two character names for SCSI devices are:
rz - RZ22, RZ23, RZ23L, RZ24, RZ55, RZ56, RZ57, RX23, RX26, RX33, RRD40, RRD42 disks
tz - TZ30, TZK50, TLZ04, TSZ05, TKZ08, and TZK10 tapes
The unit number is a combination of the SCSI bus number, either 0, 1, ... and the device's target ID number. The unit number is eight
times the bus number plus the target ID. For example, an RZ23 disk at target ID 3 on bus 0 would be referred to as rz3; a TZK50 tape at
target ID 5 on the second SCSI bus would be referred to as 13.
The SCSI bus has eight possible target device IDs. By default, one is allocated to the system. This allows for a maximum of seven target
devices connected to a SCSI bus.
Restrictions
The ULTRIX SCSI device driver does not operate with optical disks, other than the Digital-supplied devices.
The SCSI driver attempts to support on a best effort basis, non-Digital-supplied winchester disks and magnetic tapes.
The following notes apply to the driver's handling of non-Digital-supplied disks:
o These disks are assigned a device type of RZxx, instead of RZ22, RZ23, RZ23L, RZ55, RZ56, RZ57, RX23, RX26, or RX33. The RZxx disks
follow the same logical device naming scheme as the Digital-supplied disks.
o During the autoconfigure phase of the system startup, the driver prints the contents of the SCSI vendor ID, product ID, and the
revision level fields of the inquiry data return by the SCSI device.
o RZxx disks are assigned a default partition table. The default table can be modified by editing the sz_rzxx_sizes[8] entry in the
file The utility can also be used to modify the partition table on a RZxx disk.
o The only logical unit number (LUN) supported for each target ID is 0.
See Alsorz(4), tz(4), chpt(8)SCSI(4)