04-25-2010
hex editor
Hello,
I do some prove: I can intechange information between two MAC type file with the insert mode of the software "FlexHex"...but when I do the same betwwen MAc and Win file ...not work!
7 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Quick question:
When I load up Terminal or X-Windows on my Mac, and the prompt comes up...what folder am I starting in? (2 Replies)
Discussion started by: liquidcross
2 Replies
2. Solaris
Hi,
I have two Solaris machines.
1. SunOS X 5.8 Generic_108528-29 sun4u sparc SUNW,Sun-Blade-1500
2. SunOS Y 5.8 Generic_108528-13 sun4u sparc SUNW,Ultra-60
I am trying to buiild a project on both these machines. The Binary output file compiled on machine 2 runs on both the machines. Where... (0 Replies)
Discussion started by: scgupta
0 Replies
3. Windows & DOS: Issues & Discussions
Not quite sure if this is the right section, but you guys know lots of good stuff. Is there a good OS X emulator that I can put on my Windows XP system?
I have PC's and at work/lab they run everything on mac's. Due to program compatibility issues, it would be nice if I could run mac software on... (2 Replies)
Discussion started by: silkiechicken
2 Replies
4. OS X (Apple)
Hello all,
i want to install windows on mac and when i search i found that there is a program called Parallels Desktop to install windows on mac but i want it on the laptop not on the program does it work? or there is another anyway to install it on mac..??
Thanks in advanced (8 Replies)
Discussion started by: Reham$
8 Replies
5. OS X (Apple)
Hi I am mainly using unix to run programs. My current problem is that I have a hard time installing programs (binary format) on my mac. I tried install and make but it does not work.. perhaps someone can help me out.
thanks (2 Replies)
Discussion started by: phil_heath
2 Replies
6. Shell Programming and Scripting
Hi,
I have an shell script program in a remote linux machine which will do some specific monitoring functionality. Also, have some C executables in that machine.
From a windows machine, I want to run the shell script program (If possible using java).
I tried with SSH for this. but, in... (1 Reply)
Discussion started by: ram.sj
1 Replies
7. Shell Programming and Scripting
Hello *nix specialists,
Im working for a non profit organisation in Germany to transport DSL over WLAN to people in areas without no DSL. We are using Linksys WRT 54 router with DD-WRT firmware There are at the moment over 180 router running but we have to change some settings next time. So my... (7 Replies)
Discussion started by: digidax
7 Replies
LEARN ABOUT DEBIAN
setether
SETETHER(8) System Manager's Manual SETETHER(8)
NAME
setether - Set the ethernet address for use with DECnet
SYNOPSIS
setether <if> [<if>...]|all [options]
DESCRIPTION
Set ethernet MAC address on ethernet adaptors
This script should be run at system startup. It will change the ethernet hardware (MAC) address of any or all ethernet interfaces to match
the DECnet node address. DECnet requires that the MAC address of all ethernet adaptors running the protocol be set approriately. If you do
not run setether then you must change the ethernet address in some other way for DECnet to work.
By default no ethernet interfaces will have their MAC addresses changed by setether, if you specify all then all interfaces name eth* will
be changed, otherwise a list of interface names can be specified. setether will enable (UP) all interfaces it changes the MAC addresses
of.
(2.4 only) The first interface specified on the command-line will also be made the default interface for DECnet operations (ie attempts to
contact nodes not in the neighbour table will be done over this interface).
This script must be run with the interface inactive, it is normally run from /etc/init.d/decnet before TCP/IP starts up.
EXAMPLES
set the MAC address of eth0.
# /sbin/setether eth0
set the MAC address of all ethernet interfaces
# /sbin/setether all
HELPFUL HINTS
If you have multiple ethernet cards on your system and they are connected to the the same network you should specify which one you want to
use for DECnet communication on the setether command line, otherwise they will both be given the same MAC address and this is probably not
what you want.
Running DECnet on multiple ethernet interfaces only works under Linux 2.4. If you are running Linux 2.2 then the interface name on the
setether command line must match the one in /etc/decnet.conf(5).
SEE ALSO
decnet.conf(5), dntype(1), dndir(1), dndel(1), dnetd(8), dnping(1)
DECnet utilities March 01 2001 SETETHER(8)