04-22-2010
That sides= thing is printer-dependent so there's no info on that in 'man lp'. But if that option works for you, long-edge means that if you were binding them together, the long edge would be the ones stuck together, like in a three-ring binder. short-edge means that the short edge would be the one bound together, like pages in a clipboard. Your printing as landscape confuses the matter, you may need the opposite binding of what you'd normally expect.
10 More Discussions You Might Find Interesting
1. IP Networking
Hi all,
What is the difference between half duplex and full duplex? What are the advantages and disadvantages of each mode, if any?
Thanks. (3 Replies)
Discussion started by: sihong
3 Replies
2. UNIX for Dummies Questions & Answers
Ok at the moment I have a hub whit 5 computers connected to it. It's a 10/100 NetGear hub.
Ok I heard that there is some command I can run or a file I edit or something like that. But what the command/file/script/whatever does is tells you what connect speed it's connecting to the hub to.
... (4 Replies)
Discussion started by: merlin
4 Replies
3. Solaris
Hi All
I've been having a lot of errors logged on the Cisco Catalyst (4000 series) which one of my Solaris servers is patched into. I have a feeling they are duplex related, but I'm a bit stuck as to how to confirm that.
How do I:
1. Check the duplex settings on my eri0 card?
2. Set the... (3 Replies)
Discussion started by: saabir
3 Replies
4. UNIX for Dummies Questions & Answers
I am using digital Unix and lpd. I have HP 4200n LaserJet TCP printer, but when I use lpr command, it always print duplex.
I can turn off duplex feature at the panel of the printer, but then other Windows computer cannot print duplex. How can I set up /etc/printcap file so that it will be... (2 Replies)
Discussion started by: hiepng
2 Replies
5. Programming
what is meant by full duplex and half duplex?
b'coz in differences b\w hub and switch ,i heard lot this duplex word
so please help me (1 Reply)
Discussion started by: parvathy
1 Replies
6. Red Hat
how do you tell what duplex mode your box is running?
kinda like cat /proc/meminfo for memory usage..
is there a similar procedure that shows if the live kernel is running at 100-full or half etc...? (2 Replies)
Discussion started by: BG_JrAdmin
2 Replies
7. Solaris
I need to change some Ip addresses for my servers to reflect in the NIS map.
I also need to force full duplex on the 10/100 cards & 1/2 duplex in the 10 cards.
I can change the IP by doing ifconfig <NIC card > plumb up <newip>.
Not quite sure on how to force the full / half duplex & how to... (2 Replies)
Discussion started by: Remi
2 Replies
8. SuSE
How do I configure full duplex on suse 8.2
I tried
ethtool -s eth0 speed 100 duplex full autoneg off
the above works but when I reboot the machine the configure was lost.
How do I configure full duplex so that when the machine get rebooted the configuration will stay.
My interface... (4 Replies)
Discussion started by: hassan2
4 Replies
9. Solaris
Hi,
How to find whether the server is running with half duplex or full duplex. I tried with the following command ndd -get /dev/ but am not getting any output,. Is the command correct?
Also let me know how to change from half to full duplex. (1 Reply)
Discussion started by: rogerben
1 Replies
10. AIX
How to change Speed Duplex !
How to change Speed Duplex by command
chdev -P -l ent1 -a media_speed=1000_Full_Duplex
How to change Speed Duplex by Smitty .
smitty chgenet -> select adapter -> change Media speed etc. -> set "Apply change to DATABASE only" to yes -> Enter -> ... (0 Replies)
Discussion started by: ITHelper
0 Replies
LEARN ABOUT FREEBSD
if_txp
TXP(4) BSD Kernel Interfaces Manual TXP(4)
NAME
txp -- 3Com 3XP Typhoon/Sidewinder (3CR990) Ethernet interface
SYNOPSIS
To compile this driver into the kernel, place the following line in your kernel configuration file:
device txp
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
if_txp_load="YES"
DESCRIPTION
The txp interface provides access to the 10Mb/s and 100Mb/s Ethernet networks via the 3Com Typhoon/Sidewinder chipset.
Basic Ethernet functions are provided as well as support for vlan(4) tag removal and insertion assistance, receive ip(4), tcp(4), and udp(4)
checksum offloading, and transmit ip(4) checksum offloading. There is currently no support for transmit tcp(4) or udp(4) checksum offload-
ing, tcp(4) segmentation, nor ipsec(4) acceleration.
When a txp interface is brought up, by default, it will attempt to auto-negotiate the link speed and duplex mode. The speeds, in order of
attempt, are: 100Mb/s Full Duplex, 100Mb/s Half Duplex, 10 Mb/s Full Duplex, and 10 Mb/s Half Duplex.
The txp supports several media types, which are selected via the ifconfig(8) command. The supported media types are:
media autoselect
Attempt to autoselect the media type (default)
media 100baseTX mediaopt full-duplex
Use 100baseTX, full duplex
media 100baseTX [mediaopt half-duplex]
Use 100baseTX, half duplex
media 10baseT mediaopt full-duplex
Use 10baseT, full duplex
media 10baseT [mediaopt half-duplex]
Use 10baseT, half duplex
HARDWARE
The txp driver supports the following cards:
o 3Com 3CR990-TX-95
o 3Com 3CR990-TX-97
o 3Com 3cR990B-TXM
o 3Com 3CR990SVR95
o 3Com 3CR990SVR97
o 3Com 3cR990B-SRV
SEE ALSO
altq(4), arp(4), inet(4), intro(4), ip(4), miibus(4), tcp(4), udp(4), vlan(4), ifconfig(8)
HISTORY
The txp driver first appeared in OpenBSD 2.9.
BSD
January 26, 2012 BSD