04-21-2010
As Corona said, it can be done........the better question is......why? Usually when something convoluted comes up, it is to retread something that has already been implemented in a more conventional, supportable and well thought out manner.
10 More Discussions You Might Find Interesting
1. Solaris
I m having interface ce0 ce1 and its sub interfaces for that.
I want to give MAC addresses for the same.
How will I assign it.
Please give solution for the same (4 Replies)
Discussion started by: sunray
4 Replies
2. IP Networking
Hi ,
by default the physical interface (eth1) and virtual interface eth1:0 will be having same mac address, is there any way we can assign separate mac addresses for both the interfaces.
would some one help me out in this.
Thanks
Gopi (1 Reply)
Discussion started by: Gopi Krishna P
1 Replies
3. Solaris
We got a network card(e1000g0) with 1gb of speed and working with global zone. We got a new network interface card, we have to place that in slot and we have to use that card as dedicated network interface to the non-global zone(hyd_app) in V890.
As i never done this before, please explain me... (2 Replies)
Discussion started by: Sesha
2 Replies
4. Web Development
Hi,
During Nagios install we added the following piece of config to apache httpd.conf file and it runs on the regular port 80, now if I want to run this on a different port then what needs to changed to make it run on lets say port 8080.
I tried adding Virtual servers but was getting... (1 Reply)
Discussion started by: jacki
1 Replies
5. UNIX for Dummies Questions & Answers
I have 2 physical interfaces (bnx0 and bnx1) aggregated into aggr1. I need to assign second IP, and normally I know how to do it to physical interface (i.e. bnx0:1) however same trick (aggr1:1) is not working. Is there any way to do it? (0 Replies)
Discussion started by: bratan
0 Replies
6. Red Hat
Hi,
How can I config iptables to allow port forwarding from one WAN interface to second lan interface .
In my system I have one wan interface 61.93.204.56 (eth0),and lan interface 10.2.1.52(eth1)
I want to make port forward port no 22 from 61.93.204.56 to
port 22 , 10.2.1.52 , tcp and udp... (1 Reply)
Discussion started by: chuikingman
1 Replies
7. IP Networking
I have been tearing my hair out with this (and not enough left to keep going).
I have a linux box (raspberry pi) single ethernet interface in a heavily filtered DMZ with external ports fwd'd that can access an internal IP's (different subnet).
I want to forward the traffic. Should be simple I... (0 Replies)
Discussion started by: martyuiop
0 Replies
8. IP Networking
Hello all,
I am trying to receive (tcp/udp/sctp) traffic from all IPs and, eventually, all ports of an IPv6 address block using as few sockets as possible short of implementing my own network stack.
One possible solution was to associate an IP block to an interface then bind to that... (6 Replies)
Discussion started by: redwil
6 Replies
9. IP Networking
Hello,
I wanted to setup routing certain traffic (http/s) out via a second (faster) interface, like described in the following docs (may not post urls):
linux-ip.net /html/adv-multi-internet.html
thegeekstuff.com /2014/08/add-route-ip-command/
I already had this working years ago on... (0 Replies)
Discussion started by: hyphan
0 Replies
10. Solaris
Hello dears
how to assign IPv4 and IPv6 addresses with same interface on solaris 10 (1 Reply)
Discussion started by: ttashman
1 Replies
LEARN ABOUT REDHAT
xltworking
XltWorking(3X) XltWorking(3X)
NAME
XltWorking - Convenience function to display a Working dialog, and update the bar graph in the dialog.
SYNOPSIS
#include <Xlt/Xlt.h>
Boolean XltWorking(widget, question, percent_done)
Widget widget;
String question;
int percentdone;
DESCRIPTION
XltWorking Creates a dialog containing a message string, a bar showing the percentage of the task complete, and an abort button. When
called with a percent_done value of zero the dialog is managed, and a timer installed to update the bar every second. If question is not
NULL, the message string in the dialog is set to this. When called with a percent_done of 100, the dialog is un-managed. If called with a
percent_done of -1, only the message is changed. Any value between 0 and 100 will cause the bar graph to be updated the next time the timer
fires, and processes any pending timer and X events. If the return value is True, the user has requested that the task should be aborted.
widget The widget to wait for.
question
The message to display in the working dialog. Or NULL, meaning no change.
percent_done
The percentage of the task complete. 0 will cause the dialog to be managed. 100 will cause the dialog to be un-managed. -1 will
update the question only. Any value between 0 and 100 will update the bar graph.
RETURN VALUE
Boolean, if True the abort button was pushed, or the window was closed by the window manager.
RELATED INFORMATION
XltWorking(3X)