04-21-2010
As Corona said, it can be done........the better question is......why? Usually when something convoluted comes up, it is to retread something that has already been implemented in a more conventional, supportable and well thought out manner.
10 More Discussions You Might Find Interesting
1. Solaris
I m having interface ce0 ce1 and its sub interfaces for that.
I want to give MAC addresses for the same.
How will I assign it.
Please give solution for the same (4 Replies)
Discussion started by: sunray
4 Replies
2. IP Networking
Hi ,
by default the physical interface (eth1) and virtual interface eth1:0 will be having same mac address, is there any way we can assign separate mac addresses for both the interfaces.
would some one help me out in this.
Thanks
Gopi (1 Reply)
Discussion started by: Gopi Krishna P
1 Replies
3. Solaris
We got a network card(e1000g0) with 1gb of speed and working with global zone. We got a new network interface card, we have to place that in slot and we have to use that card as dedicated network interface to the non-global zone(hyd_app) in V890.
As i never done this before, please explain me... (2 Replies)
Discussion started by: Sesha
2 Replies
4. Web Development
Hi,
During Nagios install we added the following piece of config to apache httpd.conf file and it runs on the regular port 80, now if I want to run this on a different port then what needs to changed to make it run on lets say port 8080.
I tried adding Virtual servers but was getting... (1 Reply)
Discussion started by: jacki
1 Replies
5. UNIX for Dummies Questions & Answers
I have 2 physical interfaces (bnx0 and bnx1) aggregated into aggr1. I need to assign second IP, and normally I know how to do it to physical interface (i.e. bnx0:1) however same trick (aggr1:1) is not working. Is there any way to do it? (0 Replies)
Discussion started by: bratan
0 Replies
6. Red Hat
Hi,
How can I config iptables to allow port forwarding from one WAN interface to second lan interface .
In my system I have one wan interface 61.93.204.56 (eth0),and lan interface 10.2.1.52(eth1)
I want to make port forward port no 22 from 61.93.204.56 to
port 22 , 10.2.1.52 , tcp and udp... (1 Reply)
Discussion started by: chuikingman
1 Replies
7. IP Networking
I have been tearing my hair out with this (and not enough left to keep going).
I have a linux box (raspberry pi) single ethernet interface in a heavily filtered DMZ with external ports fwd'd that can access an internal IP's (different subnet).
I want to forward the traffic. Should be simple I... (0 Replies)
Discussion started by: martyuiop
0 Replies
8. IP Networking
Hello all,
I am trying to receive (tcp/udp/sctp) traffic from all IPs and, eventually, all ports of an IPv6 address block using as few sockets as possible short of implementing my own network stack.
One possible solution was to associate an IP block to an interface then bind to that... (6 Replies)
Discussion started by: redwil
6 Replies
9. IP Networking
Hello,
I wanted to setup routing certain traffic (http/s) out via a second (faster) interface, like described in the following docs (may not post urls):
linux-ip.net /html/adv-multi-internet.html
thegeekstuff.com /2014/08/add-route-ip-command/
I already had this working years ago on... (0 Replies)
Discussion started by: hyphan
0 Replies
10. Solaris
Hello dears
how to assign IPv4 and IPv6 addresses with same interface on solaris 10 (1 Reply)
Discussion started by: ttashman
1 Replies
LEARN ABOUT SUSE
ifcfg-vlan
IFCFG-VLAN(5) Network configuration IFCFG-VLAN(5)
NAME
ifcfg-vlan - virtual LAN interface configuration
SYNOPSIS
/etc/sysconfig/network/ifcfg-vlan*
Virtual LANs (802.1q)
To setup a vlan interface you need a configuration file that contains at least the mandatory
ETHERDEVICE
variable with the real interface used for the virtual LAN.
Further, it may contain the optional
VLAN_ID
variable that specifies the VLAN ID.
By default and when the VLAN_ID variable is not set, the number at the end of the interface name is the VLAN ID.
Preferably the interface name and the configuration file follow the VLAN interface name scheme (type), that is either:
ifcfg-vlan<VLAN-ID> (e.g. ifcfg-vlan42)
or
ifcfg-name.<VLAN-ID> (e.g. ifcfg-eth0.42)
The VLAN-ID can be also 0-padded (e.g. ifcfg-vlan0042 or ifcfg-eth0.0042).
Also in case of custom names, trailing digits are interpreted as VLAN-ID by default (e.g. ifcfg-dmz42). When VLAN_ID is set in the config,
the interface name have any name (e.g. ifcfg-foobar).
Note: The drawback of custom interface names and VLAN_ID usage is, that a rename of the interface is required and that they violate the
name scheme.
The real interface will be set UP automatically and doesn't need a config file in case of a physical interface. But without a config file
YaST will consider this interface as unused, if will not follow hotplug events and you're unable to apply any settings, e.g. ETH-
TOOL_OPTIONS. To avoid that, provide an config file with at least STARTMODE='auto'.
The rest of the VLAN interface IP and routes configuration do not differ from ordinary interfaces. See also man ifcfg and man routes for
details.
EXAMPLES
Sets up vlan3 vlan interface on top of eth0:
ifcfg-vlan3
STARTMODE='auto'
ETHERDEVICE='eth0'
IPADDR='192.168.3.27/24'
Sets up eth0.3 vlan interface on top of eth0:
ifcfg-eth0.3
STARTMODE='auto'
ETHERDEVICE='eth0'
IPADDR='192.168.3.27/24'
Sets up lan1 vlan interface with ID 42 on top of eth0:
ifcfg-lan1
STARTMODE='auto'
ETHERDEVICE='eth0'
VLAN_ID='42'
IPADDR='192.168.3.27/24'
BUGS
Please report bugs at <http://www.suse.de/feedback>
AUTHOR
Christian Zoz <zoz@suse.de>
Michal Svec <msvec@suse.cz>
Bjoern Jacke
Mads Martin Joergensen <mmj@suse.de>
Michal Ludvig <mludvig@suse.cz>
Marius Tomaschewski <mt@suse.de>
SEE ALSO
routes(5), ifcfg(5), ifup(8).
sysconfig August 2004 IFCFG-VLAN(5)