You should show what you have done rather than tell us the results of your efforts. This way it would be easier to tell you where you have gone wrong. Recommended reading: How to ask questions the smart way
Back to your problem: The following little sed script might do what you need, on the presumption that each line only contains one IP-address and one name, like in your example:
getting the IP address:
similar, for name:
I hope this helps.
Hi,
My input has much more lines, but few of them are below
pin(IDF) {
direction : input;
drc_pinsigtype : signal;
pin(SELDIV6) {
direction : input;
drc_pinsigtype : ... (3 Replies)
i have a file which contains alphanumeric data in every line. what i need is the data after certain pattern. the data after the pattern is not of fixed length so i need the data till the space after the pattern.
Input file:
bfdkasfbdfg khffkf lkdhfhdf pattern (datarequired data not required)... (2 Replies)
Hello,
I want to read a CSV file and look for a pattern on each line. If the pattern is found I want to read another portion/column of that line and print that. Can somebody help me in writing it in CSH?
E.g. CSV file has following lines,
1,Elephant,500kg,,,,,
2,Tiger,50kg,,,,,... (4 Replies)
I have this content in file
sshd : ALL : allow
SSHD : all : ALLOW
sshD : All : AllOW
What I need is to print the occurrence of "sshd:all" regardless of the spaces between them and if lower/upper case. So all lines should be printed in output when "grepped" or "printed... (3 Replies)
Hi Gurus, i need your help to create a script the will print a characters after the pattern was found.
Sample lines are below:
My birthday:"1977-16-07", My birthday:"1975-16-07"
My birthday:"1970-16-07".
My patter should be "birthday:", then i want to print the following characters which... (18 Replies)
Using grep I can easily use:
cvs log |grep -iB 10 -A 10 'date: 2013-10-30'
to display search results and 10 lines before and after. How can this be accompished using gawk? (4 Replies)
Hi,
I need help on a complicated file that I am working on. I wanted to extract important info from a very huge file. It is space delimited file. I have hundred thousands of records in this file. An example content of the inputfile as below:-
##
ID Ser402 Old; 23... (2 Replies)
The intended result should be :
PDF converters
'empty line'
gpdftext and pdftotext?xml version="1.0"?>
xml:space="preserve"><note-content version="0.1" xmlns:/tomboy/link" xmlns:size="http://beatniksoftware.com/tomboy/size">PDF converters
gpdftext and pdftotext</note-content>... (9 Replies)
Discussion started by: Klasform
9 Replies
9. Post Here to Contact Site Administrators and Moderators
In file, we have millions of records each of 1000 in length. And at specific position say 800 there is a space, we need to replace it with Character X if the ID in that row starts with 123.
So far i have used the below which is replacing space at that position to X but its not checking for... (3 Replies)
Hi,
I am trying to extract data based on certain conditions. My sample input file as below:-
lnc-2:1 OnePiece tra_law 500 688 1 . . g_id "R792.8417"# tra_law_id "R792.8417.1"# g_line "2.711647"# KM "8.723820"#
lnc-2:1 OnePiece room 500 510 1 . . g_id "R792.8417"# tra_law_id "R792.8417.1"#... (7 Replies)
Discussion started by: bunny_merah19
7 Replies
LEARN ABOUT DEBIAN
ocsinventory::agent::common
Ocsinventory::Agent::Common(3pm) User Contributed Perl Documentation Ocsinventory::Agent::Common(3pm)
addController()
Add a controller in the inventory.
addModem()
Add a modem in the inventory.
addDrive()
Add a partition in the inventory.
addStorages()
Add a storage system (hard drive, USB key, SAN volume, etc) in the inventory.
addMemory()
Add a memory module in the inventory.
addPort()
Add a port module in the inventory.
addSlot()
Add a slot in the inventory.
addSoftware()
Register a software in the inventory.
addMonitor()
Add a monitor (screen) in the inventory.
addVideo()
Add a video card in the inventory.
addSound()
Add a sound card in the inventory.
addNetwork()
Register a network in the inventory.
setHardware()
Save global information regarding the machine.
The use of setHardware() to update USERID and PROCESSOR* informations is deprecated, please, use addUser() and addCPU() instead.
setBios()
Set BIOS informations.
addCPU()
Add a CPU in the inventory.
addUser()
Add an user in the list of logged user.
addPrinter()
Add a printer in the inventory.
addVirtualMachine()
Add a Virtual Machine in the inventory.
addProcess()
Record a running process in the inventory.
addIpDiscoverEntry()
IpDiscover is used to identify network interface on the local network. This is done on the ARP level.
This function adds a network interface in the inventory.
setAccessLog()
What is that for? :)
flushXMlTags()
Clear the content of $common->{xmltags} (to use after adding it in XML)
POD ERRORS
Hey! The above document had some coding errors, which are explained below:
Around line 34:
'=item' outside of any '=over'
perl v5.14.2 2012-04-12 Ocsinventory::Agent::Common(3pm)