04-16-2010
Start with updating the firmware. The version you have is not just old but ancient. You should also update patches as previously mentioned.
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hello all ,
This is the output of my prtdiag command ...The speed of each of the CPUs is listed below (1281 MHz ) ..That's fine ..I'm confused about the (System clock frequency: 183 MHZ ) ..What is the difference between System Clock freq and CPU freq ...THanks..
System Configuration: Sun... (5 Replies)
Discussion started by: luft
5 Replies
2. Solaris
hi,
we have an e6900 and my sys admin says that the number of processors and memory were reduced to 4 and 8GB. However, a prtdiag |grep Memory returns 16GB of memory. So what is my system's memory? psrinfo returns 4 online and 4 offline CPUs.
Thanks.
Kumar (1 Reply)
Discussion started by: kumar27
1 Replies
3. Shell Programming and Scripting
I have sourced a property file in my script like this to load some variables in the script
Then i am able to echo all the property file values inside script but the script is not able to recognize other unix commands
#!/bin/bash
. build.properties
mkdir build
i am getting error ... (3 Replies)
Discussion started by: codeman007
3 Replies
4. Solaris
Hi,
Recently installed a Firmware patch on T5120 (solaris 10,138888-03).
The patch installation was Success and system came up fine as well. My apps are running fine too.
Problem is prtdiag does not work as it used to earlier. the output is very different from other t5120s I have and... (1 Reply)
Discussion started by: upengan78
1 Replies
5. Programming
Hi guys.
I installed eclipse now and run "Hello World" program in C. but it gives me
Launch Failed. Binary Not foundi searched in forums that say: set proper binary parser. mine is set to GNU Elf parser.
could anyone help?
My eclipse version is:
Version: 3.6.1
Build id:... (0 Replies)
Discussion started by: majid.merkava
0 Replies
6. Solaris
Hi,
i got the following error when i tried to access the cygwin x server from a windows XP PC.
"xdmcp fatal error session failed session 23 failed for display"
Alternatively, when i tried to access the same Cygwin X Server from another windows XP PC which is on a different LAN... (3 Replies)
Discussion started by: HarishKumarM
3 Replies
7. Shell Programming and Scripting
Hi All,
I have 2 properties files - one is a master templete and other one is a node specific properties file, I need to comapre these 2 properties files and make sure the node Specific properties file contains all the properties in the master temple properties file else report the missing... (5 Replies)
Discussion started by: jayka
5 Replies
8. Solaris
Hi everyone,
Please can you tell me what kind of memro we are talking about when we run :
prtdiag -v
Memory size: 98016 Megabytes
Thank you (7 Replies)
Discussion started by: adilyos
7 Replies
9. Solaris
selected lines from the output of the "prtdiag -v" command on a T5240 SUN server running Solaris 10.
Are the following known as FRU names and what do they mean?
MB/CMP0/BR0/CH0/D0
MB/CMP0/BR0/CH1/D0
SYS/FANBD0/FM0/F0
SYS/FANBD0/FM0/F1
SYS/MB/CMP0/BR1/CH0/D1 ... (1 Reply)
Discussion started by: snoman1
1 Replies
10. Solaris
I have two servers with a fresh install of Solaris 11, and having problems when doing rpcinfo between them. There is no firewall involved, so everything should theoretically be getting through. Does anyone have any ideas? I did a lot of Google searches, and haven't found a working solution yet.
... (2 Replies)
Discussion started by: christr
2 Replies
LEARN ABOUT SUSE
atmel_fwl
ATMEL_FWL(8) System Manager's Manual ATMEL_FWL(8)
NAME
atmel_fwl - Load firmware into Atmel at76c50x wireless networking chips.
SYNOPSIS
atmel_fwl <interface> /path/to/firmware
DESCRIPTION
atmel_fwl loads firmware images for Atmel at76c50x series wireless networking chips into the Linux driver for same.
Note that this utility is not normally necessary, since the driver will automatically load the correct firmware image via the hotplug sys-
tem. Atmel_fwl is provided for applications where use of the hotplug system may not be desirable.
atmel_fwl should be run after the interface has been created (after card insertion, in the case of PCMCIA cards) but before it is brought
up by running ifconfig.
NOTES
Note that there are two versions of many of the firmware images, the second one with the suffix "-wpa". These are later releases from Atmel
which support WPA privacy. They are only usable by versions of the driver greater than 0.9. Be sure not to use the "-wpa" one unless your
in-kernel driver code is version 0.9 or better. Sadly, as of version 0.9, the in-kernel driver does not actually support the setting of WPA
passphrases.
The firmware images are usually installed in /usr/lib/hotplug/firmware.
The status of the driver, including its firmware loading, is available in /proc/driver/atmel
FILES
/usr/lib/hotplug/firmware
/proc/driver/atmel
SEE ALSO
iwconfig(8), ifconfig(8),
AUTHOR
This manual page was written by Simon Kelley <simon@thekelleys.org.uk>.
ATMEL_FWL(8)