It doesn't look like zaxxon is currently online so I through this out there. Looks like the nslookup response times are good but the answering DNS server is the second one in your resolv.conf list for some reason. No DNS expert here but you might try swapping the nameserver entries around so the 10.64.40.215 is the top one.
I don't recall what the default ordering of name resolution is if the netsvc.conf file does not have an entry but you could try putting the host names in the /etc/hosts file. If I read your code correctly those are not currently there. Will look something like below:
Then vi your /etc/netsvc.conf file and enter
at the bottom of your netsvc.conf file. This would tell the system to look in the /etc/hosts file before searching the dns records.
If it doesn't help you can remove the changes I suggested.
To everyone reading if I have this wrong please correct me.
I installed Openserver 5.0.7 and I cannot telnet to the localhost and I can't telnet from my old SCO 3.2.42 to the new SCO machine but I can ping the new machine and it will telnet to the old machine. (2 Replies)
I'm trying to use rsh command to read a variable on a remote machine. I can rlogin with no problem. If I rsh HOST I also get connection like with rlogin. There is no need for passwords. But when I rsh HOST COMMAND it waits 30 seconds then gives me a connection refused error message. Any ideas?
... (4 Replies)
Hi there,
Anything will help.
I have running server on computer and want to connect from some clients.
Server:
memset(&hints, 0, sizeof(hints));
hints.ai_family = domain;
hints.ai_socktype = SOCK_STREAM;
error = getaddrinfo("localhost", "8300", &hints, &res0);
if (error)
{
... (1 Reply)
rsh is not working
command:rsh targethost -l username command
Error:Connection refused
I checked on the server rshd was not working.
Tried to start by /usr/sbin/in.rshd start
# ./in.rshd start
rshd: getpeername: Socket operation on non-socket
Please help (1 Reply)
Hi everyone,
I am hoping anyone of you could help me in this weird problem we have in 1 of our Solaris 10 servers. Lately, we have been having some ftp problems in this server. Though it can ping any server within the network, it seems that it can only ftp to a select few. For most servers, the... (4 Replies)
I dont' what happened with my servers (test servers only) but I just noticed that suddenly I cannot up the domain anymore (Sun Java System Application Server 9.1_01).
a. server.log
org.postgresql.util.PSQLException: Connection refused. Check that the hostname and port are correct and that the... (1 Reply)
Hello,
I am doing an rsh connection to server2.
I want to perform several command on server2.
I.E:
i=1
rsh server1 -l username "z=$i;`script.ksh`"
(1)Is this the right way to give z value to be used on server2?
(2) Is this the right way to run a script on server2? (1 Reply)
Hi- While trying ftp from AIX to Windows im getting below error. Can anyone share ur views on this topic.
root@AB101# ftp -n 10.192.168.68
ftp: connect: A remote host refused an attempted connect operation.
ftp>
Thanks. (3 Replies)
Hi all,
i got stuck with telnet issue, I am not able to telnet on 4001 port it show connection refused.
with default port it will open
# telnet 127.0.0.1
Trying 127.0.0.1...
Connected to 127.0.0.1.
Escape character is '^]'.
Fedora release 14 (Laughlin)
Kernel 2.6.35.6-45.fc14.i686 on... (1 Reply)
Hi, i checked on rhel VPS is running sshd
(service ssh status)
But i cant connect via putty: "Network error: Connection refused"
Please which log file in my centos rhel linux i need to watch or what are steps to do to discover cause? (3 Replies)
Discussion started by: postcd
3 Replies
LEARN ABOUT SUSE
rsh
RSH(1) BSD General Commands Manual RSH(1)NAME
rsh -- remote shell
SYNOPSIS
rsh [-Kdnx] [-k realm] [-l username] host [command]
DESCRIPTION
Rsh executes command on host.
Rsh copies its standard input to the remote command, the standard output of the remote command to its standard output, and the standard error
of the remote command to its standard error. Interrupt, quit and terminate signals are propagated to the remote command; rsh normally termi-
nates when the remote command does. The options are as follows:
-K The -K option turns off all Kerberos authentication.
-d The -d option turns on socket debugging (using setsockopt(2)) on the TCP sockets used for communication with the remote host.
-k The -k option causes rsh to obtain tickets for the remote host in realm instead of the remote host's realm as determined by
krb_realmofhost(3).
-l By default, the remote username is the same as the local username. The -l option allows the remote name to be specified. Kerberos
authentication is used, and authorization is determined as in rlogin(1).
-n The -n option redirects input from the special device /dev/null (see the BUGS section of this manual page).
-x The -x option turns on DES encryption for all data exchange. This may introduce a significant delay in response time.
If no command is specified, you will be logged in on the remote host using rlogin(1).
Shell metacharacters which are not quoted are interpreted on local machine, while quoted metacharacters are interpreted on the remote
machine. For example, the command
rsh otherhost cat remotefile >> localfile
appends the remote file remotefile to the local file localfile, while
rsh otherhost cat remotefile ">>" other_remotefile
appends remotefile to other_remotefile.
FILES
/etc/hosts
SEE ALSO rlogin(1), kerberos(3), krb_sendauth(3), krb_realmofhost(3)HISTORY
The rsh command appeared in 4.2BSD.
BUGS
If you are using csh(1) and put a rsh in the background without redirecting its input away from the terminal, it will block even if no reads
are posted by the remote command. If no input is desired you should redirect the input of rsh to /dev/null using the -n option.
You cannot run an interactive command (like rogue(6) or vi(1)) using rsh; use rlogin(1) instead.
Stop signals stop the local rsh process only; this is arguably wrong, but currently hard to fix for reasons too complicated to explain here.
Linux NetKit (0.17) August 15, 1999 Linux NetKit (0.17)