04-12-2010
You can always have a look at the /etc/rc.config.d/netconf file to see what/how interfaces are configured...
10 More Discussions You Might Find Interesting
1. Programming
Howto check if a ethernet interface is up?
It's impossible to determine via the ipaddress i have learned, or?
Can someone please give me a hint on howto do?
Environment == Linux x86 GNU GCC.
:D
regards
Esaia (2 Replies)
Discussion started by: Esaia
2 Replies
2. IP Networking
Given the interfaces on a firewall:
eth0 Link encap:Ethernet HWaddr 02:40:67:34:F5:47
inet addr:192.168.0.1 Bcast:192.168.0.255 Mask:255.255.255.0
eth1 Link encap:Ethernet HWaddr 86:23:98:45:35:56
inet addr:123.45.240.69 Bcast:255.255.255.255 ... (2 Replies)
Discussion started by: kikikaka
2 Replies
3. Solaris
Given a new Solaris box, with a fresh, unconfigured install on it, how does one figure out what kind of network interface it has (bge,le, hme, etc)? (8 Replies)
Discussion started by: akbar
8 Replies
4. HP-UX
how to get network packet size
I would like get network output rate(kb/sec)
I type command "netstat -i"
Ipkts Ierrs Opkts Oerrs 653387 0 678202 0
but i didn't know what is it packet size ,
how could i get it? (1 Reply)
Discussion started by: alert0919
1 Replies
5. Solaris
Hi,
I am using the ce interface on my Solaris 9 server and there is significant packet loss when transmitting large packets. Does anyone have a fix for this?
----10.1.0.0 PING Statistics----
51 packets transmitted, 42 packets received, 17% packet loss
round-trip (ms) min/avg/max =... (12 Replies)
Discussion started by: sparcman
12 Replies
6. Solaris
I've one Netra 240
After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces.
I tried to restart and plumb/unplumb with no luck.
ifconfig -a... (7 Replies)
Discussion started by: samer.odeh
7 Replies
7. UNIX for Dummies Questions & Answers
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
8. Shell Programming and Scripting
Hey guys, I want to use a a quick bash script/command to determine what network interface is connected to the internet so I can pipe it out to become a variable, in order so the user does not have to manually type it in each time or have to 'hardcode' the variable into the script.
I know about... (6 Replies)
Discussion started by: 3therk1ll
6 Replies
9. Solaris
Hi Folks,
Here is one for the real Solaris aficionados on the site;
I have a T5240 and have to create an I/O domain with access to the serial port, in this case /dev/term/a and although I have been through the documentation I'm having some issues in identifying the device to assign.
What I... (2 Replies)
Discussion started by: gull04
2 Replies
10. IP Networking
RHEL 7.0, IPV6
Scenario:
I have routed specific network using network scripts.
1. "ip -6 route show" shows that route has been added. ( with metric 1024)
2. Ping of the specific IP through that route is successful.
3. Now after few days, for some reason, we see that cache route appears for... (3 Replies)
Discussion started by: msr1981
3 Replies
LO(4) Kernel Interfaces Manual LO(4)
NAME
lo - software loopback network interface
SYNOPSIS
/sys/conf/SYSTEM:
NLOOP 1 # loop-back pseudo-device
DESCRIPTION
The loop interface is a software loopback mechanism which may be used for performance analysis, software testing, and/or local communica-
tion. As with other network interfaces, the loopback interface must have network addresses assigned for each address family with which it
is to be used. These addresses may be set or changed with the SIOCSIFADDR ioctl. The loopback interface should be the last interface con-
figured, as protocols may use the order of configuration as an indication of priority. The loopback should never be configured first
unless no hardware interfaces exist.
DIAGNOSTICS
lo%d: can't handle af%d. The interface was handed a message with addresses formatted in an unsuitable address family; the packet was
dropped.
SEE ALSO
intro(4N), inet(4F), ns(4F)
BUGS
Previous versions of the system enabled the loopback interface automatically, using a nonstandard Internet address (127.1). Use of that
address is now discouraged; a reserved host address for the local network should be used instead.
3rd Berkeley Distribution August 1, 1987 LO(4)