04-08-2010
Quote:
Originally Posted by
chebarbudo
I would like to use wget with the ability to select which interface to use.
Is it possible?
How can I achieve that?
Depending on how you're using wget, you can use the routing table to send traffic through the right interface (assuming different destinations for those wgets).
js.
10 More Discussions You Might Find Interesting
1. Solaris
Yes. But just wait a bit. How to do it via system calls? I'm just a newbie in Unix\Linux\Solaris e.t.c. programming. Can anyone help me? I need an advice probably how to do it or may be what API to read... :) Please, help... (2 Replies)
Discussion started by: LocalStorm
2 Replies
2. IP Networking
Hi,
I have problems with my SCO unix network interfaces.
Intel integrated adapter was failing, so I installed new one - 3COM adapter into free PCI slot.
Installed driver using SCO Software manager - successfully
Added new Network adapter using SCO Network configuration manager - successfully... (0 Replies)
Discussion started by: vilius
0 Replies
3. SCO
Hi,
I have problems with my SCO unix network interfaces.
Intel integrated adapter was failing, so I installed new one - 3COM adapter into free PCI slot.
Installed driver using SCO Software manager - successfully
Added new Network adapter using SCO Network configuration manager - successfully... (0 Replies)
Discussion started by: vilius
0 Replies
4. AIX
Hi all, this is my first post on this forum. My main problem is this:
I have a NIM server that I am trying to configure two interfaces on. One interface is for an internal Admin VLAN, the other is so that the server can use SUMA to pull updates. The problem is that I need help w/ the routing.... (0 Replies)
Discussion started by: snakernetb
0 Replies
5. AIX
Hi all, this is my first post on this forum. My main problem is this:
I have a NIM server that I am trying to configure two interfaces on. One interface is for an internal Admin VLAN, the other is so that the server can use SUMA to pull updates. The problem is that I need help w/ the routing.... (1 Reply)
Discussion started by: snakernetb
1 Replies
6. Solaris
I got second IOU in my M5000 but not able bring internal network interfcae .. ike i don't get link on those 2 interfaces .. and the same network cable plugged in PCI network card it works like a charm Is there any special way to enable the internal IOU interfaces or i have bad nics ? (8 Replies)
Discussion started by: fugitive
8 Replies
7. Debian
Hello
i am configuring a debian lenny sever ,/etc/network/interfaces is modified so that eth1 takes a static IP address
then i save it wq!
then i restart the networking , /etc/init.d/networking restart .
but after reboot ,the file is reset ,note that the interfaces had by defauklt IPv6 address... (5 Replies)
Discussion started by: learn82
5 Replies
8. UNIX for Advanced & Expert Users
All, I have a quad NIC on a V880 running Solaris 9. I've heard you can bond interfaces together and get better throughput. I found this link that seems to describe the process well. However, the command mentioned (dladm) is missing. Is there some package I need to install to get this command? Thx.... (2 Replies)
Discussion started by: agcodba
2 Replies
9. UNIX for Dummies Questions & Answers
i need a one liner command that writes in /var/log/net.log the date when i connect to the network and when i disconect ..i know that i need to write somethin in /etc/network/interfaces but idk what ! please help (1 Reply)
Discussion started by: g0dlik3
1 Replies
10. Linux
I just ran sudo service networking start on Ubuntu 16.00 and came out with error message
Job for networking service failed because control process exited with error code see systemctl status networking.service
I tried to also run this command
systemctl status networking.service
I also got an... (4 Replies)
Discussion started by: DOkuwa
4 Replies
LEARN ABOUT DEBIAN
ifscheme-mapping
IFSCHEME(8) Commands IFSCHEME(8)
NAME
ifscheme - scheme control for network interfaces
SYNOPSIS
ifscheme [-v] [[-s] newscheme]
mapping <interface> script ifscheme-mapping
DESCRIPTION
ifscheme allows you to change network configuraton schemes or query the current scheme. It integrates with the ifup(8) command and inter-
faces(5). For example, you might use this program to configure a "home" scheme and a "work" scheme for a network device on a laptop. When
you move between home and work, a simple command can reconfigure your networking.
If you run the program with no parameters, it will tell what the current network scheme is.
The ifscheme-mapping utility is used to tell the ifup and ifdown utilities about the current scheme.
OPTIONS
-v
--verbose
Run in verbose mode. This is passed in to the ifup and ifdown programs as well.
-l
--list list all schemes available/defined in /etc/network/interfaces.
newscheme
-s newscheme
--scheme newscheme
Change to a new network configuration scheme. When the scheme is changed, network interfaces that were using the old scheme will be
taken down and brought back up to use the new configuration scheme. -s or --scheme are mandatory if newscheme begins with a -.
CONFIGURATION
To make the program do anything useful when a scheme is selected, you must edit /etc/network/interfaces to add a mapping for the interface
(or interfaces) that can be controlled on a per-scheme basis. Suppose you want to control eth0 in this way. You might have an existing eth0
configuraton in there, such as:
auto eth0
iface eth0 inet static
address 192.168.1.5
netmask 255.255.255.0
gateway 192.168.1.1
To change this so you can chose between static routing and dhcp, replace it with the following (it helps to ifdown the interface first).
auto eth0
mapping eth0
script ifscheme-mapping
iface eth0-home inet static
address 192.168.1.5
netmask 255.255.255.0
gateway 192.168.1.1
iface eth0-work inet dhcp
Now if you run "ifscheme home" and ifup the interface, you'll get the eth0-home configuration stanza. If you run "ifscheme work", it will
be changed to the eth0-work stanza. You can add additional stanzas as desired, but the label must always be of the form <hardware inter-
face>-<scheme name>.
If you have a second interface (perhaps a wireless network card on eth1), you can duplicate the above for that interface, changing the eth0
and the configuration details as appropriate, but remember to add an iface stanza for every scheme name for the second interface.
FILES
/etc/network/interfaces
the interfaces definition file
/etc/network/run/scheme
the current scheme
/etc/network/run/ifstate
a record of the current state of the interfaces, managed by ifup and ifdown
BUGS
All schemed interfaces will have the same scheme.
Any schemed interface which does not have an entry for the current scheme and is not configured when the scheme is changed will not be suc-
cessfully configured when it is brought up.
SEE ALSO
interfaces(5) ifup(8) ifdown(8)
DISTRIBUTION
Redistribution is subject to the GNU public license.
AUTHORS
Joey Hess <joey@kitenet.net>, Peter Wilson <pwilson@cs.hmc.edu>
IFSCHEME(8)