Sponsored Content
Top Forums UNIX for Dummies Questions & Answers using wget on selected network interfaces Post 302411485 by chebarbudo on Thursday 8th of April 2010 03:29:24 PM
Old 04-08-2010
Question using wget on selected network interfaces

Hi there,

I have a Linux Debian server with 2 network cards each connected through a different gateway :
Code:
auto lo
iface lo inet loopback
auto eth0
iface eth0 inet static
        address 192.168.1.224
        netmask 255.255.255.0
        gateway 192.168.1.1
auto eth1
iface eth1 inet static
        address 192.168.1.225
        netmask 255.255.255.0
        gateway 192.168.1.2

I would like to use wget with the ability to select which interface to use.
Is it possible?
How can I achieve that?

Thanks for your help
Santiago
 

10 More Discussions You Might Find Interesting

1. Solaris

HOW-TO Retrieve all network interfaces??!

Yes. But just wait a bit. How to do it via system calls? I'm just a newbie in Unix\Linux\Solaris e.t.c. programming. Can anyone help me? I need an advice probably how to do it or may be what API to read... :) Please, help... (2 Replies)
Discussion started by: LocalStorm
2 Replies

2. IP Networking

Network interfaces problem

Hi, I have problems with my SCO unix network interfaces. Intel integrated adapter was failing, so I installed new one - 3COM adapter into free PCI slot. Installed driver using SCO Software manager - successfully Added new Network adapter using SCO Network configuration manager - successfully... (0 Replies)
Discussion started by: vilius
0 Replies

3. SCO

Network interfaces problem

Hi, I have problems with my SCO unix network interfaces. Intel integrated adapter was failing, so I installed new one - 3COM adapter into free PCI slot. Installed driver using SCO Software manager - successfully Added new Network adapter using SCO Network configuration manager - successfully... (0 Replies)
Discussion started by: vilius
0 Replies

4. AIX

NIM w/ two network interfaces

Hi all, this is my first post on this forum. My main problem is this: I have a NIM server that I am trying to configure two interfaces on. One interface is for an internal Admin VLAN, the other is so that the server can use SUMA to pull updates. The problem is that I need help w/ the routing.... (0 Replies)
Discussion started by: snakernetb
0 Replies

5. AIX

NIM w/ two network interfaces

Hi all, this is my first post on this forum. My main problem is this: I have a NIM server that I am trying to configure two interfaces on. One interface is for an internal Admin VLAN, the other is so that the server can use SUMA to pull updates. The problem is that I need help w/ the routing.... (1 Reply)
Discussion started by: snakernetb
1 Replies

6. Solaris

Network Interfaces

I got second IOU in my M5000 but not able bring internal network interfcae .. ike i don't get link on those 2 interfaces .. and the same network cable plugged in PCI network card it works like a charm Is there any special way to enable the internal IOU interfaces or i have bad nics ? (8 Replies)
Discussion started by: fugitive
8 Replies

7. Debian

/etc/network/interfaces problem

Hello i am configuring a debian lenny sever ,/etc/network/interfaces is modified so that eth1 takes a static IP address then i save it wq! then i restart the networking , /etc/init.d/networking restart . but after reboot ,the file is reset ,note that the interfaces had by defauklt IPv6 address... (5 Replies)
Discussion started by: learn82
5 Replies

8. UNIX for Advanced & Expert Users

How to bond network interfaces

All, I have a quad NIC on a V880 running Solaris 9. I've heard you can bond interfaces together and get better throughput. I found this link that seems to describe the process well. However, the command mentioned (dladm) is missing. Is there some package I need to install to get this command? Thx.... (2 Replies)
Discussion started by: agcodba
2 Replies

9. UNIX for Dummies Questions & Answers

/etc/network/interfaces

i need a one liner command that writes in /var/log/net.log the date when i connect to the network and when i disconect ..i know that i need to write somethin in /etc/network/interfaces but idk what ! please help (1 Reply)
Discussion started by: g0dlik3
1 Replies

10. Linux

Network interfaces error

I just ran sudo service networking start on Ubuntu 16.00 and came out with error message Job for networking service failed because control process exited with error code see systemctl status networking.service I tried to also run this command systemctl status networking.service I also got an... (4 Replies)
Discussion started by: DOkuwa
4 Replies
oidentd_masq.conf(5)						File Formats Manual					      oidentd_masq.conf(5)

NAME
oidentd_masq.conf - oidentd IP masquerading/NAT configuration file. DESCRIPTION
If you are using IP masquerading or NAT, oidentd can optionally return a username for connections from other machines. Support for this is specified by calling oidentd with the -m (or --masq) flag and by creating an /etc/oidentd_masq.conf file. oidentd can also forward requests for an IP masqueraded connection to the machine from which connection originates by way of the -f option. This will only work if the host to which the connection is forwarded is running oidentd with the -P (proxy) flag, or if the host's ident daemon will return a valid reply regardless of the input supplied by and the address of the host requesting the info (some ident daemons for windows do this, maybe others). FORMAT
<IP Address|Hostname>[/<Mask>] <Ident Response> <System Type> The first field contains the IP address or the hostname of a machine that IP masquerades through the machine on which oidentd runs. The mask parameter can be either a network mask or a mask in CIDR notation. A mask of 24 is equivalent to 255.255.255.0, a mask of 16 is equivalent to 255.255.0.0, etc. The second field specifies the reply that oidentd will return for lookups to the host matching the IP address specified in the first param- eter. The third field specifies the operating system the machine matching the first parameter is running. EXAMPLES
<Host>[/<Mask>] <Ident Response> <System Type> 192.168.1.1 someone UNIX 192.168.1.2 noone WINDOWS 192.168.1.1/32 user1 UNIX 192.168.1.0/24 user3 UNIX 192.168.0.0/16 user4 UNIX somehost user5 UNIX 192.168.1.0/255.255.255.0 user6 UNIX AUTHOR
Ryan McCabe <ryan@numb.org> http://dev.ojnk.net SEE ALSO
oidentd(8) oidentd.conf(5) version 2.0.8 13 Jul 2003 oidentd_masq.conf(5)
All times are GMT -4. The time now is 10:51 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy