How can I measure CPU loading (like performance monitor in Windows OS). I use Solaris but I would like to write portable code.
Besides, I have to write programm to load CPU with known percent. How can I use CPU in 30% for example.
Thanks for any ideas. (6 Replies)
Hi All,
Can you please help me in resolving the following problem?
My requirement is like this:
1) I have two files YESTERDAY_FILE and TODAY_FILE. Each one is having nearly two million data.
2) I need to check each record of TODAY_FILE in YESTERDAY_FILE. If exists we can skip that by... (5 Replies)
Hello guys!
I'm n00b in AIX and I'm sticked in a problem. (my English is poor enough, but I hope you can understand me :P). So.. I'm trying to connect to an AIX machine with putty, and .. 'using username xxx' appears after 2 sec (OK), but 'xxx@ip's password' appears after 1:15 min. After... (6 Replies)
Hi to all,
i have an app on solaris 5.8 writed in C++ (3.2.1) that use multi threading.
Hardware has 8 cpu. When i run my app i note that the average of cpu go at least at 40%, and the performance are not so higher..
There is a cpu limitation on solaris, that dedicate only a part of cpu... (3 Replies)
Hello All.
I have Sun T1000 server with Solaris 10.
On T1000 installed EMC smarts, application for monitoring network devices via SNMP + SNMP.
So, Smarts has own DB (contains object - devices and relationships), file takes 30 mb, now, all queries to DB works very slow, so Smarts works too slow,... (5 Replies)
Hi folks.
By disk cloning on Solaris x86, I used a command dd.
I pulled out the source and inserted the new disk.
By loading I have received the following issue: BAD PBR SIGN. :( (5 Replies)
I have written a virtual HBA driver named "xmp_vhba". A scsi disk is attached on it. as shown below:
xmp_vhba, instance #0
disk, instance #11
But the performance became very bad when we read/write the scsi disk using the vdbench(a read/write io tool).
What is the reason? ... (7 Replies)
Hello All
I have a system running AIX 61 shared uncapped partition (with 11 physical processors, 24 Virtual 72GB of Memory) .
The output from NMON, vmstat show a high run queue (60+) for continous periods of time intervals, but NO paging, relatively low I/o (6000) , CPU % is 40, Low network.... (9 Replies)
Hi,
We have a Solaris server that has about 43 Oracle databases on it and we also have the Oracle Enterprise Manager - emagent that is used to monitor these databases
When running top, the emagent is showing as one of the top process. Excerpts from running top shows something as below:
... (3 Replies)
Hi Guys,
I have fresh new installed VIO 2.2.3.70 on a p710, 3 physical SAS disks, rootvg on hdisk0
and 3 VIO clients through vscsi, AIX7.1tl4 AIX6.1tl9 RHEL6.5ppc, each lpar has its rootvg installed on a LV on datavg (hdisk2) mapped to vhost0,1,2
There is no vg on hdisk1, I use it for my... (1 Reply)
Discussion started by: frenchy59
1 Replies
LEARN ABOUT NETBSD
pmc
PMC(1) BSD General Commands Manual PMC(1)NAME
pmc -- performance-monitoring counter interface for command execution
SYNOPSIS
pmc -h
pmc -C
pmc -c event command [options ...]
DESCRIPTION
pmc is a means of using a processor's performance-monitoring counter (PMC) facility to measure various aspects of a program's execution. It
is meant to be used in a fashion similar to time(1).
The arguments are as follows:
-h Display a list of performance counter events available on the system.
-C Cancel any performance counters that are currently running.
-c event
Count the event specified by event while running the command.
DIAGNOSTICS
PMC support is not compiled into the kernel Performance-monitoring counter support has not been compiled into the kernel. It may be
included using the PERFCTRS option. See options(4) for details.
PMC counters are not supported by CPU Performance-monitoring counters are not available for the CPU.
SEE ALSO time(1), options(4)HISTORY
The pmc command first appeared in NetBSD 1.6.
AUTHORS
The pmc command was written by Frank van der Linden <fvdl@wasabisystems.com>. The kernel support for reading performance counters on the
i386 architecture was written by
Jason R. Thorpe <thorpej@zembu.com>.
BUGS
The pmc command currently only supports performance-monitoring counters on the i386 architecture.
BSD October 24, 2000 BSD