What is the command to count lines in a files, but ignore blank lines and commented lines?
I have a file with 4 sections in it, and I want each section to be counted, not including the blank lines and comments... and then totalled at the end.
Here is an example of what I would like my... (6 Replies)
Hi,
I would like to know how to solve one of my problems using expert unix commands.
I have a file with occasional blank lines;
for example;
dertu
frthu
fghtu
frtty
frtgy
frgtui
frgtu
ghrye
frhutp
frjuf
I need to edit the file so that the file looks like this; (10 Replies)
Hi all,
This should be very easy but I can't figure it out...
I have a file that looks like this:
@SRR057408.1 FW8Y5CK02R652T length=34
AGCAGTGGTATCAACGCAGAGTAAGCAGTGGTAT
+SRR057408.1 FW8Y5CK02R652T length=34
FIIHFF6666?=:88@@@BBD:::?@ABBAAA>8
@SRR057408.2 FW8Y5CK02TBMHV length=52... (1 Reply)
All I want is to look for the pattern in the file...If I found it at # places... I want print lines after those pattern(line) until I find a blank line.
Log EXAMPLE :
MT:Exception caught
The following Numbers were affected:
1234
2345
2346
Error
java.lang.InternalError:... (3 Replies)
Hi,
Consider a file named "testfile"
The contents of file are as below
first line added for test
second line added for test
third line added for test
fourth line added for test
fifth line added for test (5 Replies)
Hi,
I have a file, say files_list, as below (o/p of ls -R cmd)
$ cat files_list
/remote/dir/path/to/file:
sub-dir1
sub-dir2
sub-dir3
...
/remote/dir/path/to/file/sub-dir1:
remote_file1.csv.tgz
<blank line 1>
/remote/dir/path/to/file/sub-dir2:
remote_file2.csv.tgz
<blank... (3 Replies)
So the tag for this forum says all newbies welcome...
All I want to do is go through my file and find lines which contain a given string of characters then replace these with a blank line. I really tried to find a simple command to do this but failed.
Here's what I did come up with though:
... (2 Replies)
Dear all
I want to search special string in file and then print next all line in one line until blank lines come. Help me plz for same. My input file and desire op file is as under.
i/p file:
A1/EXT "BSCABD1_21233G1" 757 130823 1157
RADIO X-CEIVER ADMINISTRATION
BTS EXTERNAL FAULT
... (7 Replies)
Hi All
Need Help
I have a file with the below format (ABC.TXT) :
®¿¿ABCDHEJJSJJ|XCBJSKK01|M|7348974982790
HDFLJDKJSKJ|KJALKSD02|M|7378439274898
KJHSAJKHHJJ|LJDSAJKK03|F|9898982039999
(cont......)
I need to write a script where it will check for : blank lines (between rows,before... (6 Replies)
Discussion started by: chatwithsaurav
6 Replies
LEARN ABOUT V7
vp
VP(4) Kernel Interfaces Manual VP(4)NAME
vp - Versatec printer-plotter
DESCRIPTION
Vp0 is the interface to a Versatec D1200A printer-plotter with a Versatec C-PDP11(DMA) controller. Ordinarily bytes written on it are
interpreted as ASCII characters and printed. As a printer, it writes 64 lines of 132 characters each on 11 by 8.5 inch paper. Only some
of the ASCII control characters are interpreted.
NL performs the usual new-line function, i.e. spaces up the paper and resets to the left margin. It is ignored however following a CR
which ends a non-empty line.
CR is ignored if the current line is empty but is otherwise like NL.
FF resets to the left margin and then to the top of the next page.
EOT resets to the left margin, advances 8 inches, and then performs a FF.
The ioctl(2) system call may be used to change the mode of the device. Only the first word of the 3-word argument structure is used. The
bits mean:
0400 Enter simultaneous print/plot mode.
0200 Enter plot mode.
0100 Enter print mode (default on open).
040 Send remote terminate.
020 Send remote form-feed.
010 Send remote EOT.
04 Send remote clear.
02 Send remote reset.
On open a reset, clear, and form-feed are performed automatically. Notice that the mode bits are not encoded, so that it is required that
exactly one be set.
In plot mode each byte is interpreted as 8 bits of which the high-order is plotted to the left; a `1' leaves a visible dot. A full line of
dots is produced by 264 bytes; lines are terminated only by count or by a remote terminate function. There are 200 dots per inch both ver-
tically and horizontally.
When simultaneous print-plot mode is entered exactly one line of characters, terminated by NL, CR, or the remote terminate function, should
be written. Then the device enters plot mode and at least 20 lines of plotting bytes should be sent. As the line of characters (which is
20 dots high) is printed, the plotting bytes overlay the characters. Notice that it is impossible to print characters on baselines that
differ by fewer than 20 dot-lines.
In print mode lines may be terminated either with an appropriate ASCII character or by using the remote terminate function.
FILES
/dev/vp0
SEE ALSO opr(1)VP(4)