Hello,
I have two files that I need to compare and print out the line from file2 that has the first 6 fields matching the first 6 fields in file1. Complicating this are the following restrictions
1. file1 is only a few thousand lines at most and file2 is greater than 2 million
2. I need to... (7 Replies)
I have a .csv file which is seperated with (;)
inputfile
---------
ZZZZ;AAAA;BBB;CCCC;DDD;EEE;
YYYY;BBBB;CCC;DDDD;EEE;FFF;
...
...
reading file line by line till end of file.
while reading each line output format should be .
i need to print only specific columns let say 5th... (2 Replies)
Korn Shell in AIX 6.1
I want to print the below shown pipe (|) separated list line by line.
line=es349889|nhb882309|ts00293|snh03524|bg578835|bg37900|rnh00297|py882201|sg175883
for i in line
do
echo "Hello $line "
done
I wanted to execute the above for loop. But i can't even set the... (3 Replies)
Good day,
I have a list of regular expressions in file1. For each match in file2, print the containing line and the line after.
file1:
file2:
Output:
I can match a regex and print the line and line after
awk '{lines = $0} /Macrosiphum_rosae/ {print lines ; print lines } '
... (1 Reply)
Dear all
I want to search special string in file and then print next all line in one line until blank lines come. Help me plz for same. My input file and desire op file is as under.
i/p file:
A1/EXT "BSCABD1_21233G1" 757 130823 1157
RADIO X-CEIVER ADMINISTRATION
BTS EXTERNAL FAULT
... (7 Replies)
Hello,
I have below format log file,
Comparing csv_converted_files/2201/9747.1012H67126.5077292103609547345.csv and csv_converted_files/22019/97447.1012H67126.5077292103609547345.csv
Comparing csv_converted_files/2559/9447.1012H67126.5077292103609547345.csv and... (6 Replies)
example of problem:
when I echo "$e" >> /home/cogiz/file.txt
result prints to file as:AA
BB
CC
I need it to save to file as this:AA BB CC
I know it's probably something really simple but any help would be greatly appreciated.
Thank You.
Cogiz (7 Replies)
Hello,
I am looking for a specific situation in a text file. The conditions are,
> <CompoundName>
InChI=1S/C5H12NO2/c1-5(2)4-8-6(3)7/h5H,4H2,1-3H3/q+1
I am looking for cases where the line "> <CompoundName>" is followed by a line that contains the string "InChI=" without regard to... (5 Replies)
Hi All,
i want to write a shell script read below file line by line and want to exclude the lines which contains empty value for MOUNTPOINT field.
i am using centos 7 Operating system.
want to read below file.
# cat /tmp/d5
NAME="/dev/sda" TYPE="disk" SIZE="60G" OWNER="root"... (4 Replies)
Discussion started by: balu1234
4 Replies
LEARN ABOUT V7
vp
VP(4) Kernel Interfaces Manual VP(4)NAME
vp - Versatec printer-plotter
DESCRIPTION
Vp0 is the interface to a Versatec D1200A printer-plotter with a Versatec C-PDP11(DMA) controller. Ordinarily bytes written on it are
interpreted as ASCII characters and printed. As a printer, it writes 64 lines of 132 characters each on 11 by 8.5 inch paper. Only some
of the ASCII control characters are interpreted.
NL performs the usual new-line function, i.e. spaces up the paper and resets to the left margin. It is ignored however following a CR
which ends a non-empty line.
CR is ignored if the current line is empty but is otherwise like NL.
FF resets to the left margin and then to the top of the next page.
EOT resets to the left margin, advances 8 inches, and then performs a FF.
The ioctl(2) system call may be used to change the mode of the device. Only the first word of the 3-word argument structure is used. The
bits mean:
0400 Enter simultaneous print/plot mode.
0200 Enter plot mode.
0100 Enter print mode (default on open).
040 Send remote terminate.
020 Send remote form-feed.
010 Send remote EOT.
04 Send remote clear.
02 Send remote reset.
On open a reset, clear, and form-feed are performed automatically. Notice that the mode bits are not encoded, so that it is required that
exactly one be set.
In plot mode each byte is interpreted as 8 bits of which the high-order is plotted to the left; a `1' leaves a visible dot. A full line of
dots is produced by 264 bytes; lines are terminated only by count or by a remote terminate function. There are 200 dots per inch both ver-
tically and horizontally.
When simultaneous print-plot mode is entered exactly one line of characters, terminated by NL, CR, or the remote terminate function, should
be written. Then the device enters plot mode and at least 20 lines of plotting bytes should be sent. As the line of characters (which is
20 dots high) is printed, the plotting bytes overlay the characters. Notice that it is impossible to print characters on baselines that
differ by fewer than 20 dot-lines.
In print mode lines may be terminated either with an appropriate ASCII character or by using the remote terminate function.
FILES
/dev/vp0
SEE ALSO opr(1)VP(4)