03-27-2010
Hi lo-lp-kl ,
Thanks for your answer.
That model supports HMC , I downloaded from redbook IBM IntelliStation POWER 285 Technical Overview and Introduction and it supports everything what I need.
But I will have to buy standard edition of PowerVM from the link which you gave me.
10 More Discussions You Might Find Interesting
1. Linux Benchmarks
CPU/Speed: Xeon 2.4 GHz
Ram:2512M
Motherboard:
Bus:533 Mhz
Cache:
Controller:
Disk:
Load:
Kernel: RedHat AS 2.1 - 2.4.9-e.27smp
Kernel ELF?:
pgms:
BYTE UNIX Benchmarks (Version 3.11)
System -- Linux lnxdev 2.4.9-e.27smp #1 SMP Tue Aug 5 15:49:54 EDT 2003 i686 unknown
... (0 Replies)
Discussion started by: lescalp
0 Replies
2. AIX
Hello Gurus,
i'm quite new person in AIX world, actually i'm SAP consultant. But due to my job faced with AIX.
Trying to configure new server for installation SAP. We have 4 disks one of them (hdisk3) has VG rootvg. How i can extend rootvg with another disk?
i tried:
# extendvg rootvg hdisk0... (2 Replies)
Discussion started by: sapbcer
2 Replies
3. AIX
I have a 9111-520 (p5 520) that I inherited, on which I want to install AIX 5.3 or possibly 6.1.
I've installed AIX many times, on a variety of platforms, but this one isn't working for me. What I can't seem to figure out is how to set it up to boot the CD. I'm assuming there is something I... (2 Replies)
Discussion started by: thomn8r
2 Replies
4. Linux
Anyone can help me answer the question.
Why does they use Linux on IBM pSeries not AIX.
I can't understand why, cause AIX is the best supporting from IBM pSeries.
Tks you. (3 Replies)
Discussion started by: quan0509
3 Replies
5. Linux Benchmarks
CPU/Speed: 2x 3,06 GHz Xeon SL6VP
Ram: 2 GB SDRAM ECC Registriert
Motherboard: Tyan Thunder i7501 Pro (S2721-533)
Bus: 533 MHz
Cache: 512 KB
Controller: ICH3 IDE Controller
Disk: 20 GB Maxtor EIDE (2B020H1) UDMA/100
Load:
Kernel: Linux 2.6.26-2-686
Kernel ELF?: yes
pgms: gcc... (0 Replies)
Discussion started by: RudiTheStriker
0 Replies
6. AIX
Hello,
I installed PowerVM IVM Virtual I/O on P-550 but later found out that the machine isn't activated for CoD VET code for virtualization.
So when booted , it goes into OPEN Firmware
I/O Hosting requires a hosting partition boot not permitted exit called
> ok
Panel shows > IO... (3 Replies)
Discussion started by: filosophizer
3 Replies
7. AIX
Hidey Ho Folks,
Looking to buy a pServer for playing around with the IBM side of things. Looked around for a bit and notice that there is a significant price gap for the used 570's (Single Units) vs the 520's and 550's that folks are selling. Curious what to watch out for in either case? And... (6 Replies)
Discussion started by: Devyn
6 Replies
8. AIX
Solution found: dimm error!
:mad: (2 Replies)
Discussion started by: Linusolaradm1
2 Replies
9. AIX
Hello all, I am hoping someone can point me in the right direction here.
We had a machine running AIX 6.1 that someone completely corrupted, so we decided to re-load it from media. I was able to boot into DVD media, select options for complete (destructive) install, AIX standard, etc. The... (0 Replies)
Discussion started by: JamesNJ
0 Replies
10. AIX
Hi,
when I boot I get an E1DC error code. I've looked it up and it says that this error occurs during the firmware check. But the error is called "Dynamic Console Selection" .
1- Machine stopped at LCD led display = E1DC = CA00E1DC
E1DC Dynamic console selection. (maybe cable or keyboard)... (3 Replies)
Discussion started by: filosophizer
3 Replies
LEARN ABOUT OSF1
httppower
httppower(8) powerman httppower(8)
NAME
httppower - communicate with HTTP based power distribution units
SYNOPSIS
httppower [--url URL]
DESCRIPTION
httppower is a helper program for powerman which enables it to communicate with HTTP based power distribution units. It is run interac-
tively by the powerman daemon.
OPTIONS
-u, --url URL
Set the base URL.
INTERACTIVE COMMANDS
The following commands are accepted at the httppower> prompt:
auth user:pass
Authenticate to the base URL with specified user and password, using ``basic'' HTTP authentication which sends the user and password
over the network in plain text.
seturl URL
Set the base URL. Overrides the command line option.
get [URL-suffix]
Send an HTTP GET to the base URL with the optional URL-suffix appended.
post [URL-suffix] key=val[&key=val]...
Send an HTTP POST to the base URL with the optional URL-suffix appended, and key-value pairs as argument.
FILES
/usr/sbin/httppower
/etc/powerman/powerman.conf
ORIGIN
PowerMan was originally developed by Andrew Uselton on LLNL's Linux clusters. This software is open source and distributed under the terms
of the GNU GPL.
SEE ALSO
powerman(1), powermand(8), httppower(8), plmpower(8), vpcd(8), powerman.conf(5), powerman.dev(5), powerman-devices(7).
http://sourceforge.net/projects/powerman
powerman-2.3.5 2009-02-09 httppower(8)