Sponsored Content
Full Discussion: Sun Cluster-Metaset problem
Homework and Emergencies Emergency UNIX and Linux Support Sun Cluster-Metaset problem Post 302407865 by TonyFullerMalv on Friday 26th of March 2010 04:53:39 PM
Old 03-26-2010
If this is a hardware raid 5 then metastat does not come into it does it?

If the volume is not too big for the version of Solaris you are using and you are using the whole volume then might as well newfs s2 and then mount s2.
 

9 More Discussions You Might Find Interesting

1. High Performance Computing

SUN Cluster Vs Veritas Cluster

Dear All, Can anyone explain about Pros and Cons of SUN and Veritas Cluster ? Any comparison chart is highly appreciated. Regards, RAA (4 Replies)
Discussion started by: RAA
4 Replies

2. Solaris

unable to mount metaset on cluster node

Dear all, I have created a shared metaset(500gb) having 3 hosts in which 2 hosts are in cluster and 1 is non cluster. I have taken the ownership in cluster node from non cluster node but the problem is i am unable to mount the file system it is giving error "/dev/md/eccdb-ds/d100 or /eccdb-ds... (1 Reply)
Discussion started by: spandhan
1 Replies

3. Solaris

sun cluster 3.2 + oracle 11g HA problem C748634 ,C135343

Dear Cluster Guru, I had installed sc 3.2 on 2 box sunfire 240 (solaris 10 update 7 ,each node 2 gb ram) and use scsi juke box as share storage . i had test cluster application : 1. apache HA 2 oracleHA (oracle 9i) all running well (switch over between... (3 Replies)
Discussion started by: hadibn
3 Replies

4. Solaris

Sun Cluster-Metaset problem

Hi Guys i have two servers which are n cluster prd1 and prd2.. I already have a metaset configured in it..My job was to create a 1.8 tb LUN in my storage which is having Hardware raid5 pre-configured..i Created 1.8 tb with raid 5 in my storage and it got detected in both t servers prd1... (4 Replies)
Discussion started by: madanmeer
4 Replies

5. Solaris

Facing Problem with metaset in SVM

hi all, i am using solaris 5.10 on sun blade 150 and i am trying to configure diskset in sun volume manager. When i fire the following command, it says some rpc related error. bash-3.00# metaset -s kingston -a -h u15_9 metaset: u15_9: metad client create: RPC: Program not registered how to... (4 Replies)
Discussion started by: kingston
4 Replies

6. Solaris

Sun cluster and Veritas cluster question.

Yesterday my customer told me to expect a vcs upgrade to happen in the future. He also plans to stop using HDS and move to EMC. Am thinking how to migrate to sun cluster setup instead. My plan as follows leave the existing vcs intact as a fallback plan. Then install and build suncluster on... (5 Replies)
Discussion started by: sparcguy
5 Replies

7. Solaris

SVM metaset on 2 node Solaris cluster storage replicated to non-clustered Solaris node

Hi, Is it possible to have a Solaris cluster of 2 nodes at SITE-A using SVM and creating metaset using say 2 LUNs (on SAN). Then replicating these 2 LUNs to remote site SITE-B via storage based replication and then using these LUNs by importing them as a metaset on a server at SITE-B which is... (0 Replies)
Discussion started by: dn2011
0 Replies

8. Solaris

sun cluster problem

Hello everyone, Can you please help me understand what happened; here is the problem: We have a sun cluster composed by two nodes (E4900; sSolaris 9), suddenly one of them were inaccessible by PUTTY, however we were able to ping on it. The cluster haven't basculated and after 20 minutes the... (0 Replies)
Discussion started by: adilyos
0 Replies

9. Solaris

Sun cluster 4.0 - zone cluster failover doubt

Hello experts - I am planning to install a Sun cluster 4.0 zone cluster fail-over. few basic doubts. (1) Where should i install the cluster s/w binaries ?. ( global zone or the container zone where i am planning to install the zone fail-over) (2) Or should i perform the installation on... (0 Replies)
Discussion started by: NVA
0 Replies
E2LABEL(8)                                                    System Manager's Manual                                                   E2LABEL(8)

NAME
e2label - Change the label on an ext2/ext3/ext4 filesystem SYNOPSIS
e2label device [ volume-label ] DESCRIPTION
e2label will display or change the volume label on the ext2, ext3, or ext4 filesystem located on device. If the optional argument volume-label is not present, e2label will simply display the current volume label. If the optional argument volume-label is present, then e2label will set the volume label to be volume-label. Ext2 volume labels can be at most 16 characters long; if volume-label is longer than 16 characters, e2label will truncate it and print a warning message. It is also possible to set the volume label using the -L option of tune2fs(8). AUTHOR
e2label was written by Theodore Ts'o (tytso@mit.edu). AVAILABILITY
e2label is part of the e2fsprogs package and is available from http://e2fsprogs.sourceforge.net. SEE ALSO
mke2fs(8), tune2fs(8) E2fsprogs version 1.44.1 March 2018 E2LABEL(8)
All times are GMT -4. The time now is 07:26 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy