IBM pSeries Power5 9111-285 1,9 GHz Post: 302407752

10 More Discussions You Might Find Interesting

1. Linux Benchmarks

HP DL 360 Xeon 2.4 Ghz - RedHat AS 2.1

CPU/Speed: Xeon 2.4 GHz Ram:2512M Motherboard: Bus:533 Mhz Cache: Controller: Disk: Load: Kernel: RedHat AS 2.1 - 2.4.9-e.27smp Kernel ELF?: pgms: BYTE UNIX Benchmarks (Version 3.11) System -- Linux lnxdev 2.4.9-e.27smp #1 SMP Tue Aug 5 15:49:54 EDT 2003 i686 unknown ...

2. AIX

new IBM pseries and new disks

Hello Gurus, i'm quite new person in AIX world, actually i'm SAP consultant. But due to my job faced with AIX. Trying to configure new server for installation SAP. We have 4 disks one of them (hdisk3) has VG rootvg. How i can extend rootvg with another disk? i tried: # extendvg rootvg hdisk0...

3. AIX

AIX Install on 9111-520

I have a 9111-520 (p5 520) that I inherited, on which I want to install AIX 5.3 or possibly 6.1. I've installed AIX many times, on a variety of platforms, but this one isn't working for me. What I can't seem to figure out is how to set it up to boot the CD. I'm assuming there is something I...

4. Linux

Why does they use Linux on IBM pSeries

Anyone can help me answer the question. Why does they use Linux on IBM pSeries not AIX. I can't understand why, cause AIX is the best supporting from IBM pSeries. Tks you.

5. Linux Benchmarks

Tyan Thunder i7501 Pro - 2x 3,06 GHz Xeon

CPU/Speed: 2x 3,06 GHz Xeon SL6VP Ram: 2 GB SDRAM ECC Registriert Motherboard: Tyan Thunder i7501 Pro (S2721-533) Bus: 533 MHz Cache: 512 KB Controller: ICH3 IDE Controller Disk: 20 GB Maxtor EIDE (2B020H1) UDMA/100 Load: Kernel: Linux 2.6.26-2-686 Kernel ELF?: yes pgms: gcc...

6. AIX

IBM Power Pseries Open Firmware boot / VIOS POWERVM VET CODE

Hello, I installed PowerVM IVM Virtual I/O on P-550 but later found out that the machine isn't activated for CoD VET code for virtualization. So when booted , it goes into OPEN Firmware I/O Hosting requires a hosting partition boot not permitted exit called > ok Panel shows > IO...

7. AIX

IBM's pSeries 570 vs a 520 vs 550

Hidey Ho Folks, Looking to buy a pServer for playing around with the IBM side of things. Looked around for a bit and notice that there is a significant price gap for the used 570's (Single Units) vs the 520's and 550's that folks are selling. Curious what to watch out for in either case? And...

8. AIX

Strange error on 285 IBM intellistation

Solution found: dimm error! :mad:

9. AIX

Power5 9111-520 reload of AIX 6.1 - help needed

Hello all, I am hoping someone can point me in the right direction here. We had a machine running AIX 6.1 that someone completely corrupted, so we decided to re-load it from media. I was able to boot into DVD media, select options for complete (destructive) install, AIX standard, etc. The...

10. AIX

IBM AIX console pseries

Hi, when I boot I get an E1DC error code. I've looked it up and it says that this error occurs during the firmware check. But the error is called "Dynamic Console Selection" . 1- Machine stopped at LCD led display = E1DC = CA00E1DC E1DC Dynamic console selection. (maybe cable or keyboard)...

LEARN ABOUT CENTOS

enum_ieee80211_rate_flags

ENUM 
IEEE80211_RATE_(9) 					Device registration					   ENUM IEEE80211_RATE_(9)

NAME

       enum_ieee80211_rate_flags - rate flags

SYNOPSIS

       enum ieee80211_rate_flags {
	 IEEE80211_RATE_SHORT_PREAMBLE,
	 IEEE80211_RATE_MANDATORY_A,
	 IEEE80211_RATE_MANDATORY_B,
	 IEEE80211_RATE_MANDATORY_G,
	 IEEE80211_RATE_ERP_G
       };

CONSTANTS

       IEEE80211_RATE_SHORT_PREAMBLE
	   Hardware can send with short preamble on this bitrate; only relevant in 2.4GHz band and with CCK rates.

       IEEE80211_RATE_MANDATORY_A
	   This bitrate is a mandatory rate when used with 802.11a (on the 5 GHz band); filled by the core code when registering the wiphy.

       IEEE80211_RATE_MANDATORY_B
	   This bitrate is a mandatory rate when used with 802.11b (on the 2.4 GHz band); filled by the core code when registering the wiphy.

       IEEE80211_RATE_MANDATORY_G
	   This bitrate is a mandatory rate when used with 802.11g (on the 2.4 GHz band); filled by the core code when registering the wiphy.

       IEEE80211_RATE_ERP_G
	   This is an ERP rate in 802.11g mode.

DESCRIPTION

       Hardware/specification flags for rates. These are structured in a way that allows using the same bitrate structure for different bands/PHY
       modes.

AUTHOR

       Johannes Berg <johannes@sipsolutions.net>
	   Author.

COPYRIGHT

Kernel Hackers Manual 3.10					     June 2014						   ENUM IEEE80211_RATE_(9)