03-25-2010
errors on Netra-440: "IPC Warning: ipc: tcp_protocol: bad magic number"
I was asked to look into a problem with a Sun Netra 440 in another department. On the server in question, the relevant 'uname -a' information is, "SunOS host1 5.9 Generic_118558-16 sun4u sparc SUNW,Netra-440". That information aside, while the other admin is logged into the ALOM, these errors are scrolling steadily across the console:
IPC Warning: ipc: tcp_protocol: bad magic number
IPC Warning: ipc: tcp_protocol: bad magic number
IPC Warning: ipc: tcp_protocol: bad magic number
IPC Warning: ipc: tcp_protocol: bad magic number
IPC Warning: ipc: tcp_protocol: bad magic number
IPC Warning: ipc: tcp_protocol: bad magic number
I have not seen "bad magic number" messages associated with "ipc: tcp_protocol" before. Has anyone encountered and/or fixed such errors before or can anyone direct me to documentation describing IPC Warning messages on the ALOM level?
Thanks in advance for any assistance with this.
10 More Discussions You Might Find Interesting
1. Solaris
I tried rebooting my Sun server just a few minutes ago and I got the following at boot:
--
Sun Fire 280R (UltraSPARC-III+) , No Keyboard
Copyright 1998-2002 Sun Microsystems, Inc. All rights reserved.
OpenBoot 4.5, 1024 MB memory installed, Serial #xxxxxxxxx
Ethernet address... (6 Replies)
Discussion started by: deckard
6 Replies
2. Shell Programming and Scripting
Hi,
running a script fine , i get twice the following message and whether i put "set -x" , i don't see what's going wrong :
/users/notes01/scripts/sad/util/verif_boot_notes.ksh: Ma: bad number
any ideas ?
regards
Christian (4 Replies)
Discussion started by: Nicol
4 Replies
3. Filesystems, Disks and Memory
Dear All,
i have a SCSI hard disk drive i'm installing on it solaris 5 and the workstation is sun sparc, i made an image of this H.D using Norton Ghost 6, so i took off the SCSI H.D from the sun workstation and put it on a Compaq server then i booted the server from the Norton Ghost floppy disk... (0 Replies)
Discussion started by: wesweshahaha
0 Replies
4. Shell Programming and Scripting
Hallo,
i need a Prompting read in my script:
read -p "Enter your command: " command
But i always get this Error:
-p: is not an identifier
When I run these in c-shell i get this error
/usr/bin/read: read: bad option(s)
How can I use a Prompt in the read command? (9 Replies)
Discussion started by: wiseguy
9 Replies
5. AIX
Hi,
This is odd, however here goes. There are several shell scripts that run in our production environment AIX 595 LPAR m/c, which has sufficient memory 14GB (physical memory) and horsepower 5CPUs. However from time to time we get the following errors in these shell scripts. The time when these... (11 Replies)
Discussion started by: jerardfjay
11 Replies
6. Solaris
Hi
i am accessing the server remotly. i want to replace bad dvd writer. how do i know the part number of the dvd drive for raising a spare.
thanks (3 Replies)
Discussion started by: sunnybee
3 Replies
7. Shell Programming and Scripting
Hi,
I have line in input file as below:
3G_CENTRAL;INDONESIA_(M)_TELKOMSEL;SPECIAL_WORLD_GRP_7_FA_2_TELKOMSEL
My expected output for line in the file must be :
"1-Radon1-cMOC_deg"|"LDIndex"|"3G_CENTRAL|INDONESIA_(M)_TELKOMSEL"|LAST|"SPECIAL_WORLD_GRP_7_FA_2_TELKOMSEL"
Can someone... (7 Replies)
Discussion started by: shis100
7 Replies
8. Solaris
I'm posting here as it didn't seem quite right in the hardware section (as it's LOM commands). My apologies if I have that wrong though :)
I've finally gotten round to configuring the LOM on my Netra X1, but I can't get it to change the hostname via the "set" command:
lom>show hostname... (2 Replies)
Discussion started by: Smiling Dragon
2 Replies
9. AIX
Anyone running CICS TX in a WPAR ?
In my attempts to run CICS TX 5.1.0.1 in a WPAR..... CICS fails to start due to unable to load a CICS IPC Kernel Extension. The Kernel Extension is 64 bit (so not a 32 vs 64 bit issue).
Base system/LPAR is Power8 and AIX 7.1 TL3 SP5. WPAR is versioned... (4 Replies)
Discussion started by: The Doctor
4 Replies
10. Shell Programming and Scripting
Hello.
System : opensuse leap 42.3
I have a bash script that build a text file.
I would like the last command doing :
print_cmd -o page-left=43 -o page-right=22 -o page-top=28 -o page-bottom=43 -o font=LatinModernMono12:regular:9 some_file.txt
where :
print_cmd ::= some printing... (1 Reply)
Discussion started by: jcdole
1 Replies
LEARN ABOUT OPENSOLARIS
ipc
ipc.h(3HEAD) Headers ipc.h(3HEAD)
NAME
ipc.h, ipc - XSI interprocess communication access structure
SYNOPSIS
#include <sys/ipc.h>
DESCRIPTION
The <sys/ipc.h> header is used by three mechanisms for interprocess communication (IPC): messages, semaphores, and shared memory. All use a
common structure type, ipc_perm, to pass information used in determining permission to perform an IPC operation.
The ipc_perm structure contains the following members:
uid_t uid /* owner's user ID */
gid_t gid /* owner's group ID */
uid_t cuid /* creator's user ID */
gid_t cgid /* creator's group ID */
mode_t mode /* read/write permission
The uid_t, gid_t, mode_t, and key_t types are defined as described in <sys/types.h>. See types.h(3HEAD).
Definitions are provided for the constants listed below.
Mode bits:
IPC_CREAT Create entry if key does not exist.
IPC_EXCL Fail if key exists.
IPC_NOWAIT Error if request must wait.
Keys:
IPC_PRIVATE Private key.
Control commands:
IPC_RMID Remove identifier.
IPC_SET Set options.
IPC_STAT Get options.
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Interface Stability |Standard |
+-----------------------------+-----------------------------+
SEE ALSO
ftok(3C), types.h(3HEAD), attributes(5), standards(5)
SunOS 5.11 10 Sep 2004 ipc.h(3HEAD)