03-24-2010
Since you are running sysback as a cron job, where are you sending the output from the sysback? I know that at my last job, the clients that were running cron-based backups were set up so that the output from the sysback cron was sent to a log file for review the next morning.
Depending on the options you use with the sysback command line, you can get any amount of progress information for the backup: from just start/stop and logical volume progress - to a detailed progress report showing the percentage of backup completion (similar to the on screen display during an interactive backup) (this produces way too much data).
If you find the right level of verbosity for the back script and send the output to a log file, you could monitor that log file to find out the backup progress, similiar to mikep9's suggestion.
8 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi,
I need to restore my tape backup, when I type "tape status" it gives;
status : ready beginning-of-tape write-protected
soft errors : 0
hard errors : 0
underruns : 3
but... (4 Replies)
Discussion started by: alisevA3
4 Replies
2. SCO
when I do a tape status /dev/rStp0 I get the following on a new tape and I have tried several:
Status : ready beginning-of-tape
soft errors : 0
hard errors: 2
underruns: 5
My BackupEdge has stopped backing up my system because it asks for a new volume yet my total system data is under 20... (5 Replies)
Discussion started by: psytropic
5 Replies
3. AIX
We sometime run backups to tape in the background using the cron. Is there a command that will show me how fast the information is being written and or how much data has been written?
I know if we enter the information via the command prompt or smit it shows the speed and amount written. (2 Replies)
Discussion started by: daveisme
2 Replies
4. UNIX for Dummies Questions & Answers
Hi all,
We have an ESL tape library with legato networker software. From GUI - networker administrator, i can see that 3 of our tape drives are in service mode.
How can i view the same thing by issuing commands in HP-UX.
Thanks in advance! (1 Reply)
Discussion started by: *Jess*
1 Replies
5. UNIX for Dummies Questions & Answers
Do we have a way in solaris to actuallyu check in real time the activity of a tape when it is loaded for backup?
I know mt -f /dev/rmt/0n stat will provide the status. If it's busy, meaning it's currrently on backup mode or someone is using it (fuser -u /dev/rmt/0n)
I wanted to check if the... (3 Replies)
Discussion started by: lhareigh890
3 Replies
6. Solaris
Hey folks,
Linux admin here, forced to use Opensolaris to try to use ufsdump/ufsrestore to get some data of some old tapes.
I've got Opensolaris 2009.06 on x86 and a Sony SDX-700V.
As a "control" experiment, I booted the system with a Linux live CD and the tape drive worked perfectly.
... (2 Replies)
Discussion started by: eddy_sysad
2 Replies
7. HP-UX
HP rp5450 (L2000)
running HP-UX 11.11B
Using DLT 7000 and DLT 4000 tape drives for nightly full backups
Backup jobs created by SAM
DLT 7000 cron entry is as follows:
00 2 * * 1-6 /usr/sam/lbin/br_backup DLT FULL Y /dev/rmt/0m /var/sam/graphLCAa17036 root Y 1 N > /var/sam/SAM_br_msgs 2>&1... (1 Reply)
Discussion started by: dreh99
1 Replies
8. HP-UX
I have used ioscan -fnC tape and the system identified the tape drive. what is the command to show a listing of what is on the tape? I have used ls /dev/rmt/rmt0 to no avail. can anyone help?
Thanks in advance (10 Replies)
Discussion started by: Randydog
10 Replies