Sponsored Content
Full Discussion: Default route question
Operating Systems AIX Default route question Post 302406355 by gus2000 on Monday 22nd of March 2010 04:25:43 PM
Old 03-22-2010
If the routes are in ODM, they will be configured at boot. You can configure these routes anytime with "mkdev -t inet".

However, the "x.x.202.129" route is not valid for en4, since that interface is on a different subnet. Gateways must be directly reachable (i.e., on the same subnet) from a local address.
 

8 More Discussions You Might Find Interesting

1. AIX

Permanent Default Route

Hi, We are running AIX 5.2. Our default gateway used to be IP Address A. Our new default gateway is IP Address B. A netstat revealed that our default route was IP address A. We manually added default route with IP address B and removed the default route with IP address A. However,... (3 Replies)
Discussion started by: DenD
3 Replies

2. AIX

Default route removed - what to do ?

Hi, After accidental default route removal serial connection doesn't work. What should I do to connect to my machine ? thanks Vilius (7 Replies)
Discussion started by: vilius
7 Replies

3. Solaris

solaris 10 u5 what happens if no default route configured

Hi, I am new to solaris 10. What is the procedure the os takes if a default route is not configured? I am using a multihomed server with 4 interfaces. It looked strange to me this morning, because i had not defined a default route it defaulted to making one up, with the ip address of another... (9 Replies)
Discussion started by: borderblaster
9 Replies

4. Solaris

Default route is configured, but seem to not work

Hiya, I got the default gateway set in /etc/defaultrouter file, however "netstat -nr" doesn't show anything like "default" in the routing table. As far as I know "netstat" on Solaris 10 u7 should show something like : Routing Table: IPv4 Destination Gateway Flags Ref ... (8 Replies)
Discussion started by: TomSu
8 Replies

5. IP Networking

DHCP/pxeboot Situation: how to specify default route?

Greetings, I am using debian squeeze to perform the following operation: 1. pxeboot Alix 2.c board into debian installer When I get to the installer my laptop's dhcp server successfully provides an ip address but does not set up the default route. I am not sure how to provide this. I... (2 Replies)
Discussion started by: mock
2 Replies

6. AIX

Default Route add fails

AIX version 5.3 when I try to add default gateway # route add 0 192.168.100.254 Or # route add default 192.168.100.254 I get the error 0821-275 route: socket: The file access permissions do not allow the specified action. searching on google i came across similar... (5 Replies)
Discussion started by: filosophizer
5 Replies

7. Solaris

Default route in system

Hi All Recently we have faced issue in SUN server after reboot of node 2 default routs has been added to system as below IRE Table: IPv4 **Destination*************Mask***********Gateway**********Device Mxfrg Rtt***Ref Flg**Out**In/Fwd* -------------------- ---------------... (2 Replies)
Discussion started by: aaysa123
2 Replies

8. Red Hat

IP Route add default and make permanet

Hi all, actually i'm facing this problem, we have 2 NICs on our VM.s with REDHAT 7.2 release, we made the following set up as we needed to access them from both IP ip route flush all ip route add 10.130.11.0/24 dev eno2 tab 1 ip route add 10.130.10.0/24 dev eno1 tab 2 ip route add... (0 Replies)
Discussion started by: charli1
0 Replies
DUMP_SOCKDFR(8) 					      System Manager's Manual						   DUMP_SOCKDFR(8)

NAME
dump_sockdfr - Display contents of frozen route file for SOCKS server SYNOPSIS
dump_sockdfr [infile] DESCRIPTION
dump_sockdfr reads in a frozen route file for the SOCKS server and produces a listing of its contents on the standard output. The argument is optional; if omitted, /etc/sockd.fr is assumed. The frozen route file is produced by make_sockdfr and is essentially the memory image of the parsed route file. Using the frozen route file can reduce the start-up delay of the SOCKS server program since it no longer has to parse the file contents. When the SOCKS server starts, it always looks for the frozen route file /etc/sockd.fr first. If that file is not found, it then tries to use the plain-text route file /etc/sockd.route. If you use frozen route file, you must remember to run make_sockdfr every time after you modify the plain-text file or the SOCKS server will continue to use the frozen version of a previous route file. FILES
/etc/sockd.fr, /etc/sockd.route SEE ALSO
make_sockdfr(8), sockd.fr(5), sockd.route(5) AUTHOR
Ying-Da Lee, yingda@esd.sgi.com or yingda@best.com May 6, 1996 DUMP_SOCKDFR(8)
All times are GMT -4. The time now is 12:53 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy