03-20-2010
Earlier problem only used to occur after the backup was complete .
Currently i am not backing up the server but the /tmp is becoming full and when we are running the many processes on the server it use to throw the error like :
fork not enough space ..
the RAM size of my server is 8Gb and the swap space is 15 GB with this .
I guess it was due to less memory and more processes running at a time however now even i have killed several processes still /tmp space is not getting released to server .
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I just finished installing Solaris 2.6 and several applications just to realize that I made a bonehead mistake during the install. When setting up the filesystems, I entered /tmp and no swap! Is it possible to permanantly declare the entire /tmp partition as swap? I am guessing an entry in the... (4 Replies)
Discussion started by: 98_1LE
4 Replies
2. UNIX for Advanced & Expert Users
Hi,
I have a solaris 9-sparc box, which after bouncing is giving swap space related error messages(that swap space is not enough). could it be possible that there was some command issued or setting made before bouncing, which was lost after bouncing? please let me know how i can add swap space... (1 Reply)
Discussion started by: 0ktalmagik
1 Replies
3. Linux
Hi all
i am facing a problem with ext3 file system
df -h is showing 19gb is used even if there is not a single file on the mount point
/dev/mapper/vg01-archive
55G 19G 33G 36% /archive_log
OS == Linux cdrsvr 2.6.9-55.ELsmp #1 SMP Fri Apr 20 17:03:35 EDT 2007... (1 Reply)
Discussion started by: ajays
1 Replies
4. Solaris
Hi Guys !
I have found this problem many times that the swap space (/tmp space more precisely )of my Server becomes full specially when i run a complete back up of the server .
once the /tmp space is full I am not able to run simple commands as i get error like :
fork no space
on... (4 Replies)
Discussion started by: Paarth
4 Replies
5. Solaris
We have a SPARC system which is running on Solaris-9 and Physical memory size is 16GB.We have allocated 32GB SWAP space(2 times of physical memory).But when we use df -h command it shows following output and SWAP space size shows more than our allocated space
# df -h
Filesystem size used... (2 Replies)
Discussion started by: cyberdemon
2 Replies
6. UNIX for Dummies Questions & Answers
Hi all,
OS = Solaris 5.10
Without using top, can anyone please advise how to get the current swap space that is assigned to a sub-zone that is part of the Solaris zone? Some of the servers does not have the top command and I do not have access to run zone level commands either like zonecfg... (3 Replies)
Discussion started by: newbie_01
3 Replies
7. Shell Programming and Scripting
Hi Folks,
I am looking for a way to write a script to calculate swap usage in Solaris so that the current usage will be shown in Percentage value. Thanks!!
Based on 'swap -s' command
# swap -s
total: 1378936k bytes allocated + 1236880k reserved = 2615816k used, 2725104k available (2 Replies)
Discussion started by: jaapar
2 Replies
8. AIX
Hi everyone,
i have a question about the Memory Management in AIX 6.1.
I have
- 128 GB RAM and
- 70 GB Page Space.
The application i am running on this machine is doing some operations in perl. These are done only once a day and uses both memory and paging space. My problem... (1 Reply)
Discussion started by: Haichao
1 Replies
9. Linux
Hi,
i have done a blunder here, i increased the swap space on Xen5.6 server machine using below steps :-
1056 dd if=/dev/zero of=/root/myswapfile bs=1M count=1024
1057 ls -l /root/myswapfile
1058 chmod 600 /root/myswapfile
1059 mkswap /root/myswapfile
1060 swapon /root/myswapfile
... (1 Reply)
Discussion started by: apm
1 Replies
10. Solaris
Hello Team,
By the way of introduction, I am new member in this forum and proud too :)
Here is my questions:
In one of our Solaris Sparc v9 box, we are facing issues related to swap space. Our custom applications are using swap space even though physical memory is available.
From some... (3 Replies)
Discussion started by: piyush_28
3 Replies
LEARN ABOUT SUSE
killall5
KILLALL5(8) Linux System Administrator's Manual KILLALL5(8)
NAME
killall5 -- send a signal to all processes.
SYNOPSIS
killall5 -signalnumber [-o omitpid[,omitpid..]] [-o omitpid[,omitpid..]..]
DESCRIPTION
killall5 is the SystemV killall command. It sends a signal to all processes except kernel threads and the processes in its own session, so
it won't kill the shell that is running the script it was called from. Its primary (only) use is in the rc scripts found in the /etc/init.d
directory.
OPTIONS
-o omitpid
Tells killall5 to omit processes with that process id.
NOTES
killall5 can also be invoked as pidof, which is simply a (symbolic) link to the killall5 program.
EXIT STATUS
The program return zero if it killed processes. It return 2 if no process were killed, and 1 if it was unable to find any processes
(/proc/ is missing).
SEE ALSO
halt(8), reboot(8), pidof(8), killproc(8)
AUTHOR
Miquel van Smoorenburg, miquels@cistron.nl
04 Nov 2003 KILLALL5(8)