03-11-2010
10 More Discussions You Might Find Interesting
1. AIX
Hi friends,
I installed oracle 10g (10.2.0.2) RAC on 2 IBM p5 570 servers running AIX 5.3ML04 and HACMP5.2 (used Raw devices, not used GPFS). Each server has 4 x 1Gbps ethernet cards (NICs), en0 and en1 for boot address, en2 and en3 for oracle interconnect.
Now i want to merge 2 NICs (en2 and... (1 Reply)
Discussion started by: bong02
1 Replies
2. IP Networking
FreeBSD 4.8, Apache 1.3.27 - two NICs, one with a real-world IP plugged into a switch outside the PIX firewall, the other with a private IP plugged into a switch inside the PIX firewall. Apache listens on both IPs. my domain is mydomain.org.
so in /etc/rc.conf i have something like this (these... (10 Replies)
Discussion started by: ednix
10 Replies
3. Solaris
Hi, is there a way in Solaris 8 to determine how many total NIC's say a Sun Sparc box has installed - plumbed or unplumbed - and find out its capable network speeds and MAC address?
I know ifconfig -a but that only shows the plumbed and used interfaces.
thx
cc (2 Replies)
Discussion started by: bigapple100
2 Replies
4. Linux
I'm looking for a way in RHL 5.1 to use two NICs on one host with two physical IP addresses and map them under one virtual IP address, i.e. NIC 1 10.10.10.1 NIC2 10.10.10.2 VIP 192.168.10.1
Basically I want either one of the NICs to ARP for the VIP. No load balancing required just HA. (2 Replies)
Discussion started by: wschmied
2 Replies
5. UNIX for Dummies Questions & Answers
Help, I have a Ubuntu headless server that has 5 NICs in it. The eth0-4 interfaces keep moving from NIC to NIC on boot up. I am told that there is a file that I can edit that will allow me to stabilize this but I need some help in determining the exact file and format for that file. All help will... (0 Replies)
Discussion started by: poundjd
0 Replies
6. Hardware
Hi,
I have to get into BIOS and disable onbaord NICS for an IBM server, can someone please help me out.
I tried hitting F1 when reboot to get into BIOS, but it seems like a setup screen and I dont see any option to disable NICS?
Thanks
Sam (2 Replies)
Discussion started by: sam4919
2 Replies
7. IP Networking
Hi all,
Host - Ubuntu 12.04 desktop 64bit
Virtualizer - Oracle VirtualBox
2 NICs
Where can I find relevant document to set up 2 NICs, one for inward bound and another for outward bound, separate channel, both connected to the same router
Would following document be appropriate for my... (1 Reply)
Discussion started by: satimis
1 Replies
8. Red Hat
Hi All,
When I execute multipath -ll command that time display only 3 path (mpath1,mpath2 and mpath5), not display other 2 path (mpath3 and mpath4). I have configure 5 path in /etc/multipath.conf file. What is the reason behind it. Please help me.
Please find below the output :
... (5 Replies)
Discussion started by: mnmonu
5 Replies
9. Red Hat
Hi All,
When I execute "multipath -ll" command that time display only 3 path (orafra2,oradata2 and oradata1), not display other 2 path (orafra1 and data1). I have configure 5 path in "/etc/multipath.conf" file. What is the reason behind it. Please help me.
Please find below some output for... (4 Replies)
Discussion started by: mnmonu
4 Replies
10. UNIX for Dummies Questions & Answers
Hello All,
I have Linux box with two interface cards.
Every card has it's own IP Address and Gateway, IP addresses are from different subnets.
eth0 192.168.1.10/24 GW 192.168.1.1
eth1 192.168.2.10/24 GW 192.168.2.1
Third PC is located in 192.168.13.0/24 network and is trying to access... (2 Replies)
Discussion started by: AndreiM
2 Replies
LEARN ABOUT OPENSOLARIS
mp_enableautofailback
MP_EnableAutoFailback(3MPAPI) Common Multipath Management Library Functions MP_EnableAutoFailback(3MPAPI)
NAME
MP_EnableAutoFailback - enable auto-failback
SYNOPSIS
cc [ flag... ] file... -lMPAPI [ library... ]
#include <mpapi.h>
MP_STATUS MP_EnableAutoFailback(MP_OID oid);
PARAMETERS
oid The object ID of the plugin or multipath logical unit.
DESCRIPTION
The MP_EnableAutoFailback() function enables auto-failback.
RETURN VALUES
MP_STATUS_INVALID_OBJECT_TYPEkkk
The oid parameter does not specify any valid object type . This is most likely to happen if an uninitialized object ID is passed to
the AP I.
MP_STATUS_INVALID_PARAMETER
The oid parameter has a type subfield other than MP_OBJE CT_TYPE_PLUGIN or MP_OBJECT_TYPE_MULTIPATH_LU.
MP_STATUS_OBJECT_NOT_FOUND
The oid parameter owner ID or object sequence number is invalid.
MP_STATUS_SUCCESS
The operation is successful
MP_STATUS_UNSUPPORTED
The API is not supported.
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Interface Stability |Standard: ANSI INCITS 412 |
| |Multipath Management API |
+-----------------------------+-----------------------------+
|MT-Level |Safe |
+-----------------------------+-----------------------------+
SEE ALSO
libMPAPI(3LIB), MP_DisableAutoFailback(3MPAPI), attributes(5)
Multipath Management API Version 1.0
SunOS 5.11 15 Feb 2006 MP_EnableAutoFailback(3MPAPI)