|
|
Sponsored Content
Operating Systems
Solaris
Need ideas what is wrong with v440
Post 302402302 by incredible on Tuesday 9th of March 2010 11:10:54 AM
03-09-2010
|
|
10 More Discussions You Might Find Interesting
1. Solaris
Hello all,
This is probably a commonly asked question, but it has me stumped.
I have a V440 which upon bootup gives me the option of getting into ALOM with #. I don't have the ALOM password so I want to re-install Solaris 10.
When connected to the Management serial interface (on the PCI... (3 Replies)
Discussion started by: juanj
3 Replies
2. Solaris
I am looking into getting some cards for the SunFire V440. Not sure how most folks go about this but I am assuming we can find compatible cards for this server platform without going through SUN. Do you guys recommend getting this video card from SUN? Yeah we got these servers without the video... (5 Replies)
Discussion started by: bluridge
5 Replies
3. Solaris
I have a SUN V440 and it is running Solaris 9 with two NICs in the box ce0 ce1. Is there any way to get full duplex 1000? I do I check to see what ce0 and ce1 is set at and if it is not set to full duplex 1000, how do I set it and do I have to reboot the system afterward? I am new to the SUN unix... (5 Replies)
Discussion started by: pmwayne01
5 Replies
4. Solaris
I recently acquired a server for home use. Currently, I'm running a V210. I was wondering of a way to basically swap hard drives into the V440.
I would like to avoid reinstall on the V440 for many reasons.
Currently on the V440, when I try to boot up it forces itself into System Maintenance... (1 Reply)
Discussion started by: adelsin
1 Replies
5. Solaris
I'm currently trying to move a perfectly find harddrive from a V210 to a V440. From what I can tell, the disk labeling a bit different, (V210 is c1t0d0 and V440 is c0t0d0). My question is, what all do I have to change to get the V440 to boot off of this with very little complications. Right now, it... (21 Replies)
Discussion started by: adelsin
21 Replies
6. Solaris
Dear All,
I Have server SF V440, OS solaris is down and I must check logs at Sc, but I forgot my login and password.
How to reset login and password at SF V440?
Thanks
Best Regards
Jiman (3 Replies)
Discussion started by: mbah_jiman
3 Replies
7. Solaris
How do I find any available PCI slots on a v440?
When I run prtconf, I get the following output? But I am not able to make out whether all the PCI slots are used.
================================= IO Devices =================================
Bus Freq
Brd Type MHz Slot ... (1 Reply)
Discussion started by: jtamminen
1 Replies
8. UNIX and Linux Applications
Dear all,
i am in last year of electronics department in engineering faculty
i need suggestions for a graduation project based on unix or free bsd or linux and electronics "embedded linux "
i think about embedded unix for example or device drivers
please i need helps (1 Reply)
Discussion started by: MOHA-1
1 Replies
9. Shell Programming and Scripting
Hi ! all I am just trying to check range in my datafile
pls tell me why its resulting wrong
admin@IEEE:~/Desktop$ cat test.txt
0 28.4
5 28.4
10 28.4
15 28.5
20 28.5
25 28.6
30 28.6
35 28.7
40 28.7
45 28.7
50 28.8
55 28.8
60 28.8
65 28.1... (2 Replies)
Discussion started by: Akshay Hegde
2 Replies
10. Solaris
Hi,
I have Sun Solaris V440, every two days or so, the system crashes and it's at OK prompt. After that I do the FSCK and clear all the bad sectors. Then system stays up for close to 48 hours. Then it crashes again. I checked the logs and I don't see anything under /var/adm/messages file.
... (1 Reply)
Discussion started by: samnyc
1 Replies
LEARN ABOUT CENTOS
tapeinfo
TAPEINFO(1) General Commands Manual TAPEINFO(1) NAME
tapeinfo - report SCSI tape device info SYNOPSIS
tapeinfo -f <scsi-generic-device> DESCRIPTION
The tapeinfo command reads various information from SCSI tape drives that is not generally available via most vendors' tape drivers. It issues raw commands directly to the tape drive, using either the operating system's SCSI generic device ( e.g. /dev/sg0 on Linux, /dev/pass0 on FreeBSD) or the raw SCSI I/O ioctl on a tape device on some operating systems. One good time to use 'tapeinfo' is immediately after a tape i/o operation has failed. On tape drives that support HP's 'tapealert' API, 'tapeinfo' will report a more exact description of what went wrong. Do be aware that 'tapeinfo' is not a substitute for your operating system's own 'mt' or similar tape driver control program. It is intended to supplement, not replace, programs like 'mt' that access your operating system's tape driver in order to report or set information. OPTIONS
The first argument, given following -f , is the SCSI generic device corresponding to your tape drive. Consult your operating system's doc- umentation for more information (for example, under Linux these are generally start at /dev/sg0 under FreeBSD these start at /dev/pass0). Under FreeBSD, 'camcontrol devlist' will tell you what SCSI devices you have, along with which 'pass' device controls them. Under Linux, "cat /proc/scsi/scsi" will tell you what SCSI devices you have. BUGS AND LIMITATIONS
This program has only been tested on Linux with a limited number of tape drives (HP DDS4, Seagate AIT). AVAILABILITY
tapeinfo is currently being maintained by Robert Nelson <robertnelson@users.sourceforge.net> as part of the 'mtx' suite of programs. The 'mtx' home page is http://mtx.sourceforge.net and the actual code is currently available there and via SVN from http://source- forge.net/projects/mtx. SEE ALSO
mt(1),mtx(1),scsitape(1),scsieject(1),loaderinfo(1) TAPEINFO1.0 TAPEINFO(1)