|
|
Sponsored Content
Operating Systems
Solaris
Need ideas what is wrong with v440
Post 302402062 by honglus on Monday 8th of March 2010 08:14:39 PM
03-08-2010
|
|
10 More Discussions You Might Find Interesting
1. Solaris
Hello all,
This is probably a commonly asked question, but it has me stumped.
I have a V440 which upon bootup gives me the option of getting into ALOM with #. I don't have the ALOM password so I want to re-install Solaris 10.
When connected to the Management serial interface (on the PCI... (3 Replies)
Discussion started by: juanj
3 Replies
2. Solaris
I am looking into getting some cards for the SunFire V440. Not sure how most folks go about this but I am assuming we can find compatible cards for this server platform without going through SUN. Do you guys recommend getting this video card from SUN? Yeah we got these servers without the video... (5 Replies)
Discussion started by: bluridge
5 Replies
3. Solaris
I have a SUN V440 and it is running Solaris 9 with two NICs in the box ce0 ce1. Is there any way to get full duplex 1000? I do I check to see what ce0 and ce1 is set at and if it is not set to full duplex 1000, how do I set it and do I have to reboot the system afterward? I am new to the SUN unix... (5 Replies)
Discussion started by: pmwayne01
5 Replies
4. Solaris
I recently acquired a server for home use. Currently, I'm running a V210. I was wondering of a way to basically swap hard drives into the V440.
I would like to avoid reinstall on the V440 for many reasons.
Currently on the V440, when I try to boot up it forces itself into System Maintenance... (1 Reply)
Discussion started by: adelsin
1 Replies
5. Solaris
I'm currently trying to move a perfectly find harddrive from a V210 to a V440. From what I can tell, the disk labeling a bit different, (V210 is c1t0d0 and V440 is c0t0d0). My question is, what all do I have to change to get the V440 to boot off of this with very little complications. Right now, it... (21 Replies)
Discussion started by: adelsin
21 Replies
6. Solaris
Dear All,
I Have server SF V440, OS solaris is down and I must check logs at Sc, but I forgot my login and password.
How to reset login and password at SF V440?
Thanks
Best Regards
Jiman (3 Replies)
Discussion started by: mbah_jiman
3 Replies
7. Solaris
How do I find any available PCI slots on a v440?
When I run prtconf, I get the following output? But I am not able to make out whether all the PCI slots are used.
================================= IO Devices =================================
Bus Freq
Brd Type MHz Slot ... (1 Reply)
Discussion started by: jtamminen
1 Replies
8. UNIX and Linux Applications
Dear all,
i am in last year of electronics department in engineering faculty
i need suggestions for a graduation project based on unix or free bsd or linux and electronics "embedded linux "
i think about embedded unix for example or device drivers
please i need helps (1 Reply)
Discussion started by: MOHA-1
1 Replies
9. Shell Programming and Scripting
Hi ! all I am just trying to check range in my datafile
pls tell me why its resulting wrong
admin@IEEE:~/Desktop$ cat test.txt
0 28.4
5 28.4
10 28.4
15 28.5
20 28.5
25 28.6
30 28.6
35 28.7
40 28.7
45 28.7
50 28.8
55 28.8
60 28.8
65 28.1... (2 Replies)
Discussion started by: Akshay Hegde
2 Replies
10. Solaris
Hi,
I have Sun Solaris V440, every two days or so, the system crashes and it's at OK prompt. After that I do the FSCK and clear all the bad sectors. Then system stays up for close to 48 hours. Then it crashes again. I checked the logs and I don't see anything under /var/adm/messages file.
... (1 Reply)
Discussion started by: samnyc
1 Replies
LEARN ABOUT DEBIAN
locale::script
Locale::Script(3perl) Perl Programmers Reference Guide Locale::Script(3perl) NAME
Locale::Script - standard codes for script identification SYNOPSIS
use Locale::Script; $script = code2script('phnx'); # 'Phoenician' $code = script2code('Phoenician'); # 'Phnx' $code = script2code('Phoenician', LOCALE_CODE_NUMERIC); # 115 @codes = all_script_codes(); @scripts = all_script_names(); DESCRIPTION
The "Locale::Script" module provides access to standards codes used for identifying scripts, such as those defined in ISO 15924. Most of the routines take an optional additional argument which specifies the code set to use. If not specified, the default ISO 15924 four-letter codes will be used. SUPPORTED CODE SETS
There are several different code sets you can use for identifying scripts. The ones currently supported are: alpha This is a set of four-letter (capitalized) codes from ISO 15924 such as 'Phnx' for Phoenician. This code set is identified with the symbol "LOCALE_SCRIPT_ALPHA". The Zxxx, Zyyy, and Zzzz codes are not used. This is the default code set. numeric This is a set of three-digit numeric codes from ISO 15924 such as 115 for Phoenician. This code set is identified with the symbol "LOCALE_SCRIPT_NUMERIC". ROUTINES
code2script ( CODE [,CODESET] ) script2code ( NAME [,CODESET] ) script_code2code ( CODE ,CODESET ,CODESET2 ) all_script_codes ( [CODESET] ) all_script_names ( [CODESET] ) Locale::Script::rename_script ( CODE ,NEW_NAME [,CODESET] ) Locale::Script::add_script ( CODE ,NAME [,CODESET] ) Locale::Script::delete_script ( CODE [,CODESET] ) Locale::Script::add_script_alias ( NAME ,NEW_NAME ) Locale::Script::delete_script_alias ( NAME ) Locale::Script::rename_script_code ( CODE ,NEW_CODE [,CODESET] ) Locale::Script::add_script_code_alias ( CODE ,NEW_CODE [,CODESET] ) Locale::Script::delete_script_code_alias ( CODE [,CODESET] ) These routines are all documented in the Locale::Codes man page. SEE ALSO
Locale::Codes Locale::Constants http://www.unicode.org/iso15924/ Home page for ISO 15924. AUTHOR
See Locale::Codes for full author history. Currently maintained by Sullivan Beck (sbeck@cpan.org). COPYRIGHT
Copyright (c) 1997-2001 Canon Research Centre Europe (CRE). Copyright (c) 2001-2010 Neil Bowers Copyright (c) 2010-2011 Sullivan Beck This module is free software; you can redistribute it and/or modify it under the same terms as Perl itself. perl v5.14.2 2011-09-26 Locale::Script(3perl)