Hi
Someone logged on the system with a Normal user and changed the password , for this user , how can i know ? who changed the password from which terminal ?
regards
Georges (5 Replies)
Hi,
At the moment, I have inserted an actual filename to conduct searches through it etc... Instead, I want the user to choose a filename and then do the searches against this file, instead of already having specified the file in the code. How would I do this? I tried doing the following, but it... (5 Replies)
Hi ,,, i just come across this forum and i make it a must to be pay a visit here everyday and through it am learning a lots of things which am sure i will be able to share later...
So i have a prob with my pc when i try to change my Ip address in the dos command using ipconfig command i got a... (1 Reply)
Discussion started by: Lutchumaya
1 Replies
4. Post Here to Contact Site Administrators and Moderators
I work on a UNIX HP 10.20 system that recently crashed. I am new with UNIX but I pick things up quick. The system I work on consists of two computers with the same basic hardware config. I have been having trouble loading the program software it uses, NOT the UNIX software, so I used the a... (1 Reply)
Hello,
I want to write a ksh script about changing UID and changing group with GID. There are multiple servers i want to perform that job.
linux1
linux2
linux3
linux4
linux5 ......
.
.
.
.
.
1.) How can i enter "password" in script rather asking me?
I was trying this...
ssh... (2 Replies)
Hi experts
I have to change the default router of some system
I tried changing by deleing the existing route by following line
#route delete default 172.24.2.101
then I added executed the below line to add the new router
#route add default 172.24.1.254
... (9 Replies)
Write a shell program to replace the starting alphabet "a" with "k" for the file names in the current directory.
Note : Change only the file names starting with "a". Rest of the file names remains unchanged.
Homework. Replies deleted. Closed. (0 Replies)
Hi all
Im trying to learn the basics of bash and am struggling with some file manipulation. I am trying to run a script that once you have logged in allows you to change your password which is held (along with the corresponding username) in a different file called usernames. When i try to run my... (2 Replies)
I have a input file like this
select column1,column2 from tablename where column3='1000000001';
select column1,column2 from tablename where column3='1000000002';
select column1,column2 from tablename where column3='1000000003';
select column1,column2 from tablename where column3='1000000004';... (4 Replies)
Discussion started by: nsuresh316
4 Replies
LEARN ABOUT FREEBSD
snd_maestro
SND_MAESTRO(4) BSD Kernel Interfaces Manual SND_MAESTRO(4)NAME
snd_maestro -- ESS Maestro bridge device driver
SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file:
device sound
device snd_maestro
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
snd_maestro_load="YES"
DESCRIPTION
The snd_maestro bridge driver allows the generic audio driver sound(4) to attach to ESS Maestro based sound chips. This chipset is very pop-
ular in notebook computers, but it is also very used in a wide selection of cheap OEM sound cards.
HARDWARE
The snd_maestro driver supports the following PCI sound cards:
o ESS Technology Maestro-1
o ESS Technology Maestro-2
o ESS Technology Maestro-2E
SEE ALSO snd_maestro3(4), sound(4)HISTORY
The snd_maestro device driver first appeared in FreeBSD 4.2.
AUTHORS
This manual page was written by Jorge Mario G. Mazo <jgutie11@eafit.edu.co>.
BSD December 15, 2005 BSD