03-03-2010
I was able to connect a laptop using the same IP info I added to the AIX server so I am uncertain what changes need to be made to the ARP table or the routing table for the AIX server could you elaborate more on the topic and perhaps include the commands to view the routing and ARP tables?
Thanks
10 More Discussions You Might Find Interesting
1. IP Networking
We are unable to bring one of our linux boxes into the network once it was restarted. But once we stop and start the network service. We are able to ping the gateway and get into network. After a minute or two we get the following reponse for the ping command
64 bytes from 124.168.215.40:... (6 Replies)
Discussion started by: chrisanto_2000
6 Replies
2. IP Networking
Hello this is my first post at this forum.
Apologize for my lack of network understanding
but Im posting to learn.
I have a problem reaching default gateway 10.18.110.1
If I use my laptop I can ping 10.18.110.1 but with our red hat multihomed server the gateway does not respond to ping.
cat... (11 Replies)
Discussion started by: vettec3
11 Replies
3. Solaris
I was install new solaris10 on m4000 model after that i "ping -s" to default gateway but it's take longtime (2 Min) to reply and if i use "ping" only it's reply to fase(2 sec). any body who can tell me about my problem and how to fix it please. i'm try to fix several days. (2 Replies)
Discussion started by: cesmk
2 Replies
4. Red Hat
I know the subject line is very similar to: destination host unreachable
but the problem with my machine appears to be somewhat different from that thread. apologies if I missed something from there.
We recently moved a machine physically and from one subnet to another . I used... (1 Reply)
Discussion started by: mirage
1 Replies
5. AIX
Just want to know if someone has a clue about what could be happening here:
I have an AIX box with four NICs in Ether channel connected to a Cisco Switch.
When I try to ping the default gateway, sometimes it works, but sometimes it doesn't work unless it has a defined static route.
Thanks... (1 Reply)
Discussion started by: witt
1 Replies
6. UNIX for Dummies Questions & Answers
I have NCR MP-RAS unix. I have been trying for several months to get our network working since we had never used it before. I have setup all routes that I can think of. I know it has something to do with the routing table, because out of sheer luck I was able to get it working, and than like a... (4 Replies)
Discussion started by: Rutgerncas
4 Replies
7. AIX
I just reinstalled a fresh install of 5300 07 on an old 44p model 170, after installing I set an IP Address on en2 and I tried to the ping default gateway, no response. I tried a
startsrc -g tcpip
... and then I can ping the default gateway. I broke the ping and tried again to ping. I cannot... (1 Reply)
Discussion started by: asyed123
1 Replies
8. Red Hat
Hi,
Here is the issue: There are 2 identical systems in the same subnet here. They can ping and ssh each other. One can ping the default gateway and one can not with error '... icmp_seq Destination Host Unreachable'. I can't find any difference between the two systems in terms of network... (4 Replies)
Discussion started by: aixlover
4 Replies
9. AIX
Hi,
I installed AIX 7.1 on a blade though (hmc with vio). I can ping the IP address, but not the gateway. Is there anything that I should configure?
Is there anything that I have to check with vio setting or Am I missing any configuration?
Please let me know further.
Thank you (5 Replies)
Discussion started by: pjeedu2247
5 Replies
10. UNIX for Advanced & Expert Users
I have setup a Linux machine on my server but for some reason Im unable to reach my default gateway. This is causing me to not communicate with the outside world (unable to connect to CentOS repos)
# ifconfig
enp0s3: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet... (3 Replies)
Discussion started by: Junaid Subhani
3 Replies
IPX_CMD(8) System Manager's Manual IPX_CMD(8)
NAME
ipx_cmd - bridge between Novell's SCMD driver and local IPX network
SYNOPSIS
ipx_cmd -A server name [ -l local interface name ]
DESCRIPTION
ipx_cmd moves packets from tapN to server and vice versa. It is something like IPX Tunnel, but it uses Novell Netware 5 server Compatibil-
ity Mode Driver (AKA Migration Agent) on the other end of wire. You must first configure your kernel tapN device with IPX EthernetII frame
and with network number set up on server (you can use kernel autodetection).
OPTIONS
-A server name
This is IP name of compatibility mode server. You can use DNS name or dotted quad to specify server address.
-l local interface name
This allows you to specify, which of your IP addresses should be used as IP address of client side of CMD driver. You must configure
your tapN device with hardware address 7E:01:AA:BB:CC:DD, where AA:BB:CC:DD is your IP address in hexa.
EXAMPLE
If you are on server platan.vc.cvut.cz (147.32.240.81) and your migration agent runs on server boris.vc.cvut.cz, you can configure your
system with:
insmod ethertap
ifconfig tap0 hw ether 7E:01:93:20:F0:51 up
ipx_interface add -p tap0 EtherII
ipx_cmd -A boris.vc.cvut.cz -l 147.32.240.81 &
BUGS
This program was written to satisfy my own needs and should be really improved. At least it should configure tap interface itself.
AUTHOR
Petr Vandrovec <vandrove@vc.cvut.cz>
ipx_cmd IPX Utilities IPX_CMD(8)