Hi all,
I tried to use this command
ndd -set /dev/eri adv_1000fdx_cap 1
but i get a "operation failed, Invalid argument"
anyone can help ? Thanks (5 Replies)
I have a TOSHIBA AS7000 B150 Sun Box
I wanted to run it with 100M/full duplex
I had added this to the /etc/system file to make to setting permenant So it would be set correctly on reboot.
set eri:eri_adv_100fdx_cap=1
set eri:eri_adv_100hdx_cap=0
set eri:eri_adv_autoneg_cap=0
But when I... (4 Replies)
I recently learned that Sun Solaris network cards (ce devices) have problems with ndd -get commands. I did some searching and found out about the netstat -k command to show me the link speed. What is the best way to change the link speed (both one time and permanently)?
I am running Solaris 9... (7 Replies)
Hi there
We have a bit of a debate going here over what the prefered method is for setting 1000/Full on e1000g or nge interfaces is.
As you aware the Solaris configration files for nge and e1000g dont allow you to "fix" 1000/Full but instead allow you to set auto-negotiate to ON but only... (1 Reply)
Hi,
In UNIX, it's very easy to find the duplex speed. But in Windows, is there a easy way to find the duplex speed? I can't go to over 100 servers to find this out, I was wondering if I run one command to do this?
Please advice. (2 Replies)
Evening,
I am attempting to change the speed and duplex settings on a single interface on a bge card on an m3000 SPARC server. Currently the settings are as follows:
bge0 link: up speed: 1000 Mbps duplex: full
bge1 link: up speed: 100 Mbps ... (13 Replies)
Hi,
How to find whether the server is running with half duplex or full duplex. I tried with the following command ndd -get /dev/ but am not getting any output,. Is the command correct?
Also let me know how to change from half to full duplex. (1 Reply)
how can we change the nic card speed
please explain through commands & steps ????
and i want to change NIC speed 100 --1000Mbps
and what is full & half duplex gives
thanks in advance (6 Replies)
VIO Server connected to switch port and running with half duplex speed on one of the shared ethernet adapter. We have verified at switch end and everythings looks good.
Other ethernet adapter in the VIO server are connected and running in Full duplex speed.
Please help me find why this shared... (4 Replies)
Discussion started by: mugunthanvh
4 Replies
LEARN ABOUT DEBIAN
colorgccrc
COLORGCCRC(5) File Formats Manual COLORGCCRC(5)NAME
colorgccrc - configuration file for colorgcc
DESCRIPTION
A colorgccrc configuration file is used to configure the highlighting of the compiler output from colorgcc.
SYNTAX
Each line consists of a keyword designating a configuration variable. The keyword is followed by `:' and then one or several values
(depending on the keyword). Lines beginning with a hash mark `#' are comments.
CONFIGURATION VARIABLES
g++ | gcc | c++ | cc | g77 | gcj | gnat | gpc
Specifies the paths to the compilers. Takes one value; a path to the compiler.
nocolor
Specifies what terminal types colorization should be disabled on. Takes one or several values, separated by whitespace.
srcColor
Specifies the highlighting attributes source-code should be given. Takes one or several color attributes. See the section COLOR
ATTRIBUTES for more information.
introColor
Specifies the highlighting attributes for normal compiler output. Takes one or several color attributes. See the section COLOR
ATTRIBUTES for more information.
warningFileNameColor | errorFileNameColor
Specifies the highlighting attributes for the filename in a warning or an error, respectively. Takes one or several color
attributes. See the section COLOR ATTRIBUTES for more information.
warningNumberColor | errorNumberColor
Specifies the highlighting attributes for the line-number in a warning or an error, respectively. Takes one or several color
attributes. See the section COLOR ATTRIBUTES for more information.
warningMessageColor | errorMessageColor
Specifies the highlighting attributes for the message-text in a warning or an error, respectively. Takes one or several color
attributes. See the section COLOR ATTRIBUTES for more information.
COLOR ATTRIBUTES
The following attributes are valid for highlighting.
clear, reset
bold, underline, underscore, blink, reverse, concealed
black, red, green, yellow, blue, magenta, cyan, white
on_black, on_red, on_green, on_yellow, on_blue, on_magenta, on_cyan, on_white
SEE ALSO gcc(1), colorgcc(1)HISTORY
Jan 15 2003: Initial version of this manual-page.
REPORTING BUGS
Report bugs to <jmoyers@geeks.com>
AUTHORS
Jamie Moyers <jmoyers@geeks.com> is the author of colorgcc.
This manual page was written by Joe Wreschnig <piman@sacredchao.net>, and modified by David Weinehall <tao@debian.org>, for the Debian
GNU/Linux system (but may be used by others).
COPYRIGHT
Copyright (C) 2003 Jamie Moyers
This is free software; see the source for copying conditions. There is NO warranty; not even for MERCHANTABILITY or FITNESS FOR A PARTICU-
LAR PURPOSE.
Jan 15, 2003 COLORGCCRC(5)