03-02-2010
Both are sparc machines and the application is using scp (F-secure I think) to measure 'speed'. The server A has a qfe card - the tcp_host_param is set on only one of the interfaces and it has 1.3MBs versus 512MBs to the interface with the default tcp_host_param setting.
Again, the question is what parameter (if any) would need to be set to get the same type of boost (obviously the tcp_host_param doesn't do it anymore - actually, the transfer does use the tcp_host_param setting when the scp happens [can be seen with netstat -an send-q/recv-q] but it doesn't cause it to go any faster, as it did between 2 Solaris 8 servers).
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hello,
I am totally new to Unix. My current contract requires me to build an intranet site (nothing fancy, no forms, no cgi scripts, no search engine) for a unix platform.
I develop on an NT environment using dreamweaver.
I am considering buying Red Hat Linux, install that on the NT... (1 Reply)
Discussion started by: alam
1 Replies
2. IP Networking
I am trying to set an interface to 100/Full, but the command I use are getting rejected. I think it is the last argument, but I don't know how to find the correct values.
I am trying to use the following script, but change hme to le .
echo "Setting hme interface 1: 100mb/full-duplex..."
... (2 Replies)
Discussion started by: bbrandeb49
2 Replies
3. Solaris
Hi Guys,
I need help with ndd.
I was going through network FAQ but i have more questions then answers regarding ndd.
#ndd -set /dev/hme instance 0
#ndd -set /dev/hme adv_100fdx_cap 1
#ndd -set /dev/hme adv_100hdx_cap 0
#ndd -set /dev/hme adv_10fdx_cap 0
#ndd -set /dev/hme adv_10hdx_cap 0... (2 Replies)
Discussion started by: nitinkgoud
2 Replies
4. Solaris
Hi, Anyone can help
My solaris 8 system has the following
/dev/null , /dev/tty and /dev/console
All permission are lrwxrwxrwx
Can this be change to a non-world write ??
any impact ?? (12 Replies)
Discussion started by: civic2005
12 Replies
5. Solaris
Hi,
I would like to know whether there is any config file that i can refer to for the result of 'ndd -get /dev/tcp tcp_time_wait_interval'?
When i man 'ndd', there is one statement which is -> Each driver chooses which parameters to make visible using ndd. Does it answering my question above... (3 Replies)
Discussion started by: honmin
3 Replies
6. Solaris
Solaris 10 server (SunOS 5.10 Generic_137137_09)
I have a services file configured in /etc in there windows clients connect to my server on port 6034-6037
when I do the following
netstat | grep TestServices
it pulls all the connections active for those ports
so right now I have 10 clients... (3 Replies)
Discussion started by: deaconf19
3 Replies
7. SCO
While in SCO Openserver 5.0.7, Sybase listened to /dev/inet/tcp, the same is not working in SCO Openserver 6. The Network card is however active and pinging fine. What can be the reason? What is the way out?
An early response will be appreciated.
Thank you
Regards
TCG (2 Replies)
Discussion started by: thecobolguy
2 Replies
8. Red Hat
on RHEL 5.3 i did
mount -o remount,rw /dev/hda8 ( this is /tmp directory )
now OS not coming up.
How to resolve ??
---------- Post updated at 04:57 PM ---------- Previous update was at 03:36 PM ----------
one of my friend told me that you have changed sticky bit permissions on /tmp... (6 Replies)
Discussion started by: rehantayyab82
6 Replies
9. Solaris
Hello forum,
I have a Solaris 9 Sun Fire v240 server and Sun Fire v440
Recently we made changes and installed a new switch which both of them are connected to it. Cisco Catalyst 3750.
Now the Sun Server v240 is having problems with the network. It was supposed to run at 1000mbs speed.
ndd... (10 Replies)
Discussion started by: br1an
10 Replies
10. Shell Programming and Scripting
I have a command to check the status of hostname and port number,
echo > /dev/tcp/hostname/80
echo $?
0
success case
echo > /dev/tcp/hostname/809999
I got the output
-------------------
connection timed out
It took almost 4 minutes to time out,,, how can I set it to 10 seconds?
my... (2 Replies)
Discussion started by: sam@sam
2 Replies
ndd(1M) System Administration Commands ndd(1M)
NAME
ndd - get and set driver configuration parameters
SYNOPSIS
ndd [-set] driver parameter [value]
DESCRIPTION
ndd gets and sets selected configuration parameters in some kernel drivers. Currently, ndd only supports the drivers that implement the
TCP/IP Internet protocol family. Each driver chooses which parameters to make visible using ndd. Since these parameters are usually
tightly coupled to the implementation, they are likely to change from release to release. Some parameters may be read-only.
If the -set option is omitted, ndd queries the named driver, retrieves the value associated with the specified parameter, and prints it. If
the -set option is given, ndd passes value, which must be specified, down to the named driver which assigns it to the named parameter.
By convention, drivers that support ndd also support a special read-only parameter named ``?'' which can be used to list the parameters
supported by the driver.
EXAMPLES
Example 1: Getting Parameters Supported By The TCP Driver
To see which parameters are supported by the TCP driver, use the following command:
example% ndd /dev/tcp ?
The parameter name ``?'' may need to be escaped with a backslash to prevent its being interpreted as a shell meta character.
The following command sets the value of the parameter ip_forwarding in the dual stack IP driver to zero. This disables IPv4 packet forward-
ing.
example% ndd -set /dev/ip ip_forwarding 0
Similarly, in order to disable IPv6 packet forwarding, the value of parameter ip6_forwarding
example% ndd -set /dev/ip ip6_forwarding 0
To view the current IPv4 forwarding table, use the following command:
example% ndd /dev/ip ipv4_ire_status
To view the current IPv6 forwarding table, use the following command:
example% ndd /dev/ip ipv6_ire_status
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWcsu |
+-----------------------------+-----------------------------+
SEE ALSO
nca(1), ioctl(2), attributes(5), arp(7P), ip(7P), ip6(7P), tcp(7P), udp(7P)
NOTES
The parameters supported by each driver may change from release to release. Like programs that read /dev/kmem, user programs or shell
scripts that execute ndd should be prepared for parameter names to change.
The ioctl() command that ndd uses to communicate with drivers is likely to change in a future release. User programs should avoid making
dependencies on it.
The meanings of many ndd parameters make sense only if you understand how the driver is implemented.
SunOS 5.10 8 Nov 1999 ndd(1M)