02-26-2010
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
hi. Im trying to install a switch.
And the manual says i should type a command including a SerialPortDevicePath. which is the filepath to serial port used for connection.
However.. nothing about how to find this info.
Could anyone help me where to find this path?
thx
mr.T (6 Replies)
Discussion started by: tyskertøs
6 Replies
2. Programming
I am trying to access DG-100 gps logger on Mac OS X with POSIX API. The device uses a Prolific usb-serial controller, and connect to the usb port on my mac.
After I install the Prolific driver, it shows up as /dev/tty.usbserial and /dev/cu.usbserial. The vendor has published the data format. So... (1 Reply)
Discussion started by: monkeybiz
1 Replies
3. Linux
Hey!
I'm trying to figure out a sollution for a problem I have at my company with an Iomega MiniMax 500 GB USB disk.
If i run cat /proc/bus/usb/devices
I get this information:
T: Bus=01 Lev=02 Prnt=04 Port=00 Cnt=01 Dev#= 5 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00... (2 Replies)
Discussion started by: noratx
2 Replies
4. Ubuntu
Hello!
I am working on an application which reads environmental instruments which have serial ports. The application requires a serial port to be present to talk to the device (i.e. /dev/ttyS0 ). In some instances the environmental devices will be 100's of yards away from the computer, so a... (5 Replies)
Discussion started by: mvona
5 Replies
5. Shell Programming and Scripting
My input is a long list of data start with "#":
#read_1
123456898787987
#read_2
54645646540646406
#read_3
4654564654316
.
.
I got a bit confusing about how to set all in an array first. And then when I run a program name "statistic_program", it will read the array in scalar and do... (24 Replies)
Discussion started by: patrick87
24 Replies
6. AIX
Hi Everyone,
The machine I'm working on is an AIX 5.3 LPAR running on a P650. oslevel -r shows 5300-08. I'm trying to take a backup to a SCSI tape drive, which has been working up until this point. I know of nothing that has changed recently to cause this problem. But when I try to take a... (0 Replies)
Discussion started by: need2bageek
0 Replies
7. SCO
I am trying to change one of my serial printers from /dev/ttyr002 to /dev/ttyr014:
lpstat -s
device for check3: /dev/ttyr002
device for check4: /dev/ttyr002
I changed the tty setting for check3 in:
/etc/printcap
/var/spool/lp/admins/lp/printers/check3
to /dev/ttyr014
Then I get:... (4 Replies)
Discussion started by: herot
4 Replies
8. Programming
hi, I've a problem on my C/C++ program with Posix Library.
I have to read data from the serial but I have incorrect data, in fact I get a bunch of zeros:
"2953.3174, 2785.2126, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0 , 0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0 ,... (24 Replies)
Discussion started by: enaud
24 Replies
9. Programming
Hi
I try to communicate with a GSM modem, from C, for sending SMS.
I use standart AT-commands.
Working well with terminal.
There is no problem writing ti the port.
But when I try to read I only get a echo, I write "ATI" and get "ATI" back, I should get somthing like "SIEMENS 35... (4 Replies)
Discussion started by: dmiller
4 Replies
10. Shell Programming and Scripting
I'm new to Linux (Ubuntu 16.04), and very new to BASH scripting. I have a Numato 8-channel USB GPIO device, which is a DAQ that appears in the system as a serial port. In Linux it appears as ttyACM0. I can easily manipulate a GPO with, for example:
echo "gpio set 7" > /dev/ttyACM0
...followed... (12 Replies)
Discussion started by: Chalk-X
12 Replies
LEARN ABOUT DEBIAN
edit-patch
EDIT-PATCH(1) General Commands Manual EDIT-PATCH(1)
NAME
edit-patch, add-patch - tool for preparing patches for Debian source packages
SYNOPSIS
edit-patch path/to/patch
add-patch path/to/patch
DESCRIPTION
edit-patch is a wrapper script around the Quilt, CDBS, and dpatch patch systems. It simplifies the process of preparing and editing patches
to Debian source packages and allows the user to not have to be concerned with which patch system is in use. Run from inside the root
directory of the source package, edit-patch can be used to edit existing patches located in debian/patches.
It can also be used to incorporate new patches. If pointed at a patch not already present, it will copy the patch to debian/patches in the
correct format for the patch system in use. Next, the patch is applied and a subshell is opened in order to edit the patch. Typing exit
or pressing Ctrl-d will close the subshell and launch an editor to record the debian/changelog entry.
edit-patch is integrated with the Bazaar and Git version control systems. The patch will be automatically added to the tree, and the
debian/changelog entry will be used as the commit message.
If no patch system is present, the patch is applied inline, and a copy is stored in debian/patches-applied.
add-patch is the non-interactive version of edit-patch. The patch will be incorporated but no editor or subshell will be spawned.
AUTHORS
edit-patch was written by Daniel Holbach <daniel.holbach@canonical.com>, Michael Vogt <michael.vogt@canonical.com>, and David Futcher
<bobbo@ubuntu.com>.
This manual page was written by Andrew Starr-Bochicchio <a.starr.b@gmail.com>.
Both are released under the terms of the GNU General Public License, version 3.
DEBIAN
Debian Utilities EDIT-PATCH(1)