02-24-2010
You have 68 zombie process in your server which causes the performance degrade. Please kill all these processes and check if becomes normal.
Thanks,
Deepak
9 More Discussions You Might Find Interesting
1. Solaris
Guys where can i find values to add in /etc/system to make sun solaris 10 working better ? im sure there is alot of values but i dont know from where i can find them if you know any please send direct and if you know another sites send links to it, thanks so much. (5 Replies)
Discussion started by: XP_2600
5 Replies
2. UNIX for Advanced & Expert Users
Dear Sun gurus,
I have Sun Fire V240 server with its StorEdge 3300 disk-array. Following are its disks appeared in format command. I have prepared its partitions thru format and metainit & metattach (may be i have made wrong steps, causing the errors below because I have done thru some document... (1 Reply)
Discussion started by: shafeeq
1 Replies
3. Solaris
Hello All.
I have Sun T1000 server with Solaris 10.
On T1000 installed EMC smarts, application for monitoring network devices via SNMP + SNMP.
So, Smarts has own DB (contains object - devices and relationships), file takes 30 mb, now, all queries to DB works very slow, so Smarts works too slow,... (5 Replies)
Discussion started by: hemulll
5 Replies
4. Filesystems, Disks and Memory
Hello,
i have a a1000 connected to an e6500. There's a raid 10 (12 disks) on the a1000.
If i do a
dd if=/dev/zero of=/mnt/1 bs=1024k count=1000
and then look at iostat it tells me there's a kw/s of 25000.
But if i do a
dd of=/dev/zero if=/mnt/1 bs=1024k count=1000
then i see only a... (1 Reply)
Discussion started by: mbrenner
1 Replies
5. Solaris
Hi,
I want to know if there is a command available for obtaining the BIOS Serial Number on a Sun Fire V240 machine? Or is it a known issue that it cannot be obtained through any command?
Thanks,
Vineet (4 Replies)
Discussion started by: vineetd
4 Replies
6. Solaris
hallo anybody know how to set alom mail alerty server with yahoomail ?
thank u?where i can find mail server address for yahoomail?thank (1 Reply)
Discussion started by: yanto85
1 Replies
7. Solaris
I have a sun fire v240 server.
The output of prtdiag -v shows a failed fan.
There are 3 fans for cooling system board.
There is 1 fan for each of the powersupply (There are 2 powersupplies)
From the below output how do i know which fan is bad and whats its location... (3 Replies)
Discussion started by: Tirmazi
3 Replies
8. Solaris
Hi All, I'm new to this site. I have a few question since I'm in the process how to to repair my raid on Sun V240 Server.
1. How can we create RAID in Sun Sparc v240?
2. What utility can help people create RAID in Sun Sparc v240?
3. Do we need any special software to create the... (12 Replies)
Discussion started by: angkor
12 Replies
9. Solaris
Hi
If you had a choice of processor for a general purpose web server, either:
A. T1, 8-core. (in a T1000, 8GB, 72GB SAS x 2)
or
B. Dual 1.6GHZ USIIIi (in a Sun Blade 2500 Silver Workstation, 4GB, 146GB SCSI)
Would A be significantly better than B?
Even on single-threaded tasks?
I... (0 Replies)
Discussion started by: edik
0 Replies
LEARN ABOUT FREEBSD
killall
KILLALL(1) BSD General Commands Manual KILLALL(1)
NAME
killall -- kill processes by name
SYNOPSIS
killall [-delmsvz] [-help] [-I] [-j jail] [-u user] [-t tty] [-c procname] [-SIGNAL] [procname ...]
DESCRIPTION
The killall utility kills processes selected by name, as opposed to the selection by PID as done by kill(1). By default, it will send a TERM
signal to all processes with a real UID identical to the caller of killall that match the name procname. The super-user is allowed to kill
any process.
The options are as follows:
-d | -v Be more verbose about what will be done. For a single -d option, a list of the processes that will be sent the signal will be
printed, or a message indicating that no matching processes have been found.
-e Use the effective user ID instead of the (default) real user ID for matching processes specified with the -u option.
-help Give a help on the command usage and exit.
-I Request confirmation before attempting to signal each process.
-l List the names of the available signals and exit, like in kill(1).
-m Match the argument procname as a (case sensitive) regular expression against the names of processes found. CAUTION! This is
dangerous, a single dot will match any process running under the real UID of the caller.
-s Show only what would be done, but do not send any signal.
-SIGNAL Send a different signal instead of the default TERM. The signal may be specified either as a name (with or without a leading
``SIG''), or numerically.
-j jail Kill processes in the specified jail.
-u user Limit potentially matching processes to those belonging to the specified user.
-t tty Limit potentially matching processes to those running on the specified tty.
-c procname Limit potentially matching processes to those matching the specified procname.
-q Suppress error message if no processes are matched.
-z Do not skip zombies. This should not have any effect except to print a few error messages if there are zombie processes that
match the specified pattern.
ALL PROCESSES
Sending a signal to all processes with the given UID is already supported by kill(1). So use kill(1) for this job (e.g. ``kill -TERM -1'' or
as root ``echo kill -TERM -1 | su -m <user>'').
IMPLEMENTATION NOTES
This FreeBSD implementation of killall has completely different semantics as compared to the traditional UNIX System V behavior of killall.
The latter will kill all processes that the current user is able to kill, and is intended to be used by the system shutdown process only.
EXIT STATUS
The killall utility exits 0 if some processes have been found and signalled successfully. Otherwise, a status of 1 will be returned.
DIAGNOSTICS
Diagnostic messages will only be printed if requested by -d options.
SEE ALSO
kill(1), pkill(1), sysctl(3), jail(8)
HISTORY
The killall command appeared in FreeBSD 2.1. It has been modeled after the killall command as available on other platforms.
AUTHORS
The killall program was originally written in Perl and was contributed by Wolfram Schneider, this manual page has been written by Jorg
Wunsch. The current version of killall was rewritten in C by Peter Wemm using sysctl(3).
BSD
June 30, 2013 BSD