02-24-2010
You have 68 zombie process in your server which causes the performance degrade. Please kill all these processes and check if becomes normal.
Thanks,
Deepak
9 More Discussions You Might Find Interesting
1. Solaris
Guys where can i find values to add in /etc/system to make sun solaris 10 working better ? im sure there is alot of values but i dont know from where i can find them if you know any please send direct and if you know another sites send links to it, thanks so much. (5 Replies)
Discussion started by: XP_2600
5 Replies
2. UNIX for Advanced & Expert Users
Dear Sun gurus,
I have Sun Fire V240 server with its StorEdge 3300 disk-array. Following are its disks appeared in format command. I have prepared its partitions thru format and metainit & metattach (may be i have made wrong steps, causing the errors below because I have done thru some document... (1 Reply)
Discussion started by: shafeeq
1 Replies
3. Solaris
Hello All.
I have Sun T1000 server with Solaris 10.
On T1000 installed EMC smarts, application for monitoring network devices via SNMP + SNMP.
So, Smarts has own DB (contains object - devices and relationships), file takes 30 mb, now, all queries to DB works very slow, so Smarts works too slow,... (5 Replies)
Discussion started by: hemulll
5 Replies
4. Filesystems, Disks and Memory
Hello,
i have a a1000 connected to an e6500. There's a raid 10 (12 disks) on the a1000.
If i do a
dd if=/dev/zero of=/mnt/1 bs=1024k count=1000
and then look at iostat it tells me there's a kw/s of 25000.
But if i do a
dd of=/dev/zero if=/mnt/1 bs=1024k count=1000
then i see only a... (1 Reply)
Discussion started by: mbrenner
1 Replies
5. Solaris
Hi,
I want to know if there is a command available for obtaining the BIOS Serial Number on a Sun Fire V240 machine? Or is it a known issue that it cannot be obtained through any command?
Thanks,
Vineet (4 Replies)
Discussion started by: vineetd
4 Replies
6. Solaris
hallo anybody know how to set alom mail alerty server with yahoomail ?
thank u?where i can find mail server address for yahoomail?thank (1 Reply)
Discussion started by: yanto85
1 Replies
7. Solaris
I have a sun fire v240 server.
The output of prtdiag -v shows a failed fan.
There are 3 fans for cooling system board.
There is 1 fan for each of the powersupply (There are 2 powersupplies)
From the below output how do i know which fan is bad and whats its location... (3 Replies)
Discussion started by: Tirmazi
3 Replies
8. Solaris
Hi All, I'm new to this site. I have a few question since I'm in the process how to to repair my raid on Sun V240 Server.
1. How can we create RAID in Sun Sparc v240?
2. What utility can help people create RAID in Sun Sparc v240?
3. Do we need any special software to create the... (12 Replies)
Discussion started by: angkor
12 Replies
9. Solaris
Hi
If you had a choice of processor for a general purpose web server, either:
A. T1, 8-core. (in a T1000, 8GB, 72GB SAS x 2)
or
B. Dual 1.6GHZ USIIIi (in a Sun Blade 2500 Silver Workstation, 4GB, 146GB SCSI)
Would A be significantly better than B?
Even on single-threaded tasks?
I... (0 Replies)
Discussion started by: edik
0 Replies
KILL(1) Linux Programmer's Manual KILL(1)
NAME
kill - terminate a process
SYNOPSIS
kill [ -s signal | -p ] [ -a ] [ -- ] pid ...
kill -l [ signal ]
DESCRIPTION
The command kill sends the specified signal to the specified process or process group. If no signal is specified, the TERM signal is sent.
The TERM signal will kill processes which do not catch this signal. For other processes, it may be necessary to use the KILL (9) signal,
since this signal cannot be caught.
Most modern shells have a builtin kill function, with a usage rather similar to that of the command described here. The `-a' and `-p'
options, and the possibility to specify pids by command name is a local extension.
OPTIONS
pid... Specify the list of processes that kill should signal. Each pid can be one of five things:
n where n is larger than 0. The process with pid n will be signaled.
0 All processes in the current process group are signaled.
-1 All processes with pid larger than 1 will be signaled.
-n where n is larger than 1. All processes in process group n are signaled. When an argument of the form `-n' is given, and it
is meant to denote a process group, either the signal must be specified first, or the argument must be preceded by a `--'
option, otherwise it will be taken as the signal to send.
commandname
All processes invoked using that name will be signaled.
-s signal
Specify the signal to send. The signal may be given as a signal name or number.
-l Print a list of signal names. These are found in /usr/include/linux/signal.h
-a Do not restrict the commandname-to-pid conversion to processes with the same uid as the present process.
-p Specify that kill should only print the process id (pid) of the named processes, and not send any signals.
SEE ALSO
bash(1), tcsh(1), kill(2), sigvec(2), signal(7)
AUTHOR
Taken from BSD 4.4. The ability to translate process names to process ids was added by Salvatore Valente <svalente@mit.edu>.
Linux Utilities 14 October 1994 KILL(1)