02-21-2010
Sun TTY
Thanks for your input. Unfortunately, I cannot enter anything at the OBP OK prompt. That is the problem. There are not two monitor cards in the machine. There is only the on-board VGA port. Unfortunately, my monitor does not permit manual setup. It is auto-tune only, and when it detects some sort of VGA signal, it will adjust itself to that signal. I have a KVM, and it works fine on the other 3 machines it is connected to; including the HP-UX system which only supports 1024x768 when it boots.
This cable did work fine until I made the upgrades. I installed Solaris 10 without issue, and was able to make StarOffice work for me after it was on the network. But you're correct about the pinouts. I carefully checked the serial connector; there are no bent pins.
I'm beginning to think that the mainboard on this thing is busted. It worked fine with the less RAM and disk before the upgrade. Maybe I did something to it and broke it somewhere along the way.
This sucks; I am out of work and cannot afford a new SunBlade. I need this machine to learn Sun's virtualization and ZFS. These need to be on my resume so I can get some work.
10 More Discussions You Might Find Interesting
1. Solaris
hii alll
i have a problem with my sunblade100. when i switch on, no display comes but if i ping from a remote machine its pinging,but iam not able to telent to that sun server,what can be the problem,how can i sort ot this issue
2 thing in usb iam not able to use STOP N (to clear the... (3 Replies)
Discussion started by: solaris8in
3 Replies
2. Debian
I have tried to install the Debian distribution for SPARC processor, but is a pian in the neck trying to boot from cdrom or floppy.
Please can somebody to help me to know the easiest way to boot and install Debian on a SUNBLADE 100 system? or wich is the best way to installed on this system, I... (2 Replies)
Discussion started by: GEIER
2 Replies
3. Solaris
Hi all,
I am a newbies here,
Have question regards large hard disk install in SunBlade system.
Can SunBlade 150 support 2 x 160GB (internal IDE) ?
Want to make sure before buy the hard disks.
Anyone had experiences configure large hard disk in SunBlade 150 before ?
In the SunBlade 150... (2 Replies)
Discussion started by: ong.kianseng
2 Replies
4. Solaris
Hi guys,
I have a SunBlade 2000 that I am trying to configure. It has been configured previously with an IP address, hostname, DNS and so forth. I want to configure it with a new IP address. How can I achieve this? It has been one of the most difficult tasks for me as I am not really... (6 Replies)
Discussion started by: Arkayev
6 Replies
5. UNIX for Dummies Questions & Answers
Hi everyone this is my first post
I have used linux a couple of times and was impressed, so i bought an old sunblade 1000, just to learn something new.
I cannot get the thing to work! I have tried to install solaris 10 and several types of linux. I am beginning to wonder if i was sold a... (3 Replies)
Discussion started by: Kawakaze
3 Replies
6. Solaris
Greetings,
I was in the mood of upgrading my sunblade100 in my bedroom, since I recuperated some RAM from intel servers, and found myself with what seems to not work (I was hoping to pass from 256Mb to 2GB... and then upgrading to solaris 10...)
after this failure I tried with just one 512 MB,... (2 Replies)
Discussion started by: vbe
2 Replies
7. Solaris
Good Morning,
I took a mirror drive from one Solaris 9 machine and used it to set up another. After syncing another mirror on the second machine I restarted but I don't get a login screen.
I see a message:The X-server cannot be started on display :0
Also during startup I see:... (8 Replies)
Discussion started by: Stellaman1977
8 Replies
8. UNIX for Beginners Questions & Answers
Good Afternoon,
I'm setting up a SunBlade 2500 using ufsrestoreand have gotten to the point where I have restored the root and usr partitions. However, the machine keeps rebooting, never really coming up. Looking at vfstab, it looks pretty empty- shouldn't I see entries like... (22 Replies)
Discussion started by: Stellaman1977
22 Replies
9. Shell Programming and Scripting
In bash, you can do something like this:
#!/bin/bash
echo -n "What is your name? " > /dev/tty
read thename < /dev/tty
How can I do the same in python?
I have a python script that has the following content:
#!/usr/bin/python2.7
import getpass
import sys
import telnetlib
import... (2 Replies)
Discussion started by: SkySmart
2 Replies
10. UNIX for Beginners Questions & Answers
Hi.
I have a Microsystems SunBlade 150
shell# cat /etc/release
Solaris 8 2/02 s28s_u7wos_08a SPARC
shell# uname -a
SunOS HOSTNAME 5.8 Generic_108528-14 sun4u sparc SUNW,Sun-Blade-100
shell# prtconf -F
/pci@1f,0/SUNW,m64B@13:m640
When I join to the only account the server try to... (5 Replies)
Discussion started by: siegroup
5 Replies