Login or Register to Ask a Question and Join Our Community

Sponsored Content
Full Discussion: How to install a network card
Top Forums UNIX for Dummies Questions & Answers How to install a network card Post 302391850 by chebarbudo on Tuesday 2nd of February 2010 05:24:17 PM
Old 02-02-2010
Hi Pludi,

Thanks, you're right, ifconfig -a shows somthing different:
I had a eth2_rename directive somewhere, went to modify /etc/udev/rules.d/70-persistent-net.rules and it all works fine now.

Thank you very much!
Santiago
 

10 More Discussions You Might Find Interesting

1. IP Networking

network card

I have a UnixWare 2 server that has an ISA 3Com NIC that has just a BNC connector on it. I want to remove this and install an ISA 3Com NIC that has a BNC/RJ45 connector. What steps do I have to go through to successfully complete this? Thye are almost the exact same cards except for the... (1 Reply)
Discussion started by: cparks
1 Replies

2. UNIX for Advanced & Expert Users

Network Card Help

I have been having trouble with my sis900 neytwork card in slacwkare linux. I tried to modprobe the sis900, it didnt give me any errors but it didnt load it. so I put in a realtek 8139 network card and tried it too. These are the errors i get with the two cards when trying to do insmod on either of... (3 Replies)
Discussion started by: The Fridgerator
3 Replies

3. UNIX for Advanced & Expert Users

network card problem

hi, everyone: alpha 600 au true64 Unix 4.0f my network cart is set "Auto-Negotiate".After operate system startup,the network will be disconnected by itself at sometime. I found some prompt in /usr/adm/messages. "tu0 :transmit FIFO underflow:threshold raised to :256 byteŁ¬link up... (1 Reply)
Discussion started by: q30
1 Replies

4. UNIX for Dummies Questions & Answers

Network card and internet

Hi!. I have problems installing my network card under ther redhat kernel. First i tryed my integrated intel pro set 10/100 then my d-link 530tx Pci but none of them seems to be found. also i huse my network card to connect to the net trough PPPOE where i need to type my username and... (3 Replies)
Discussion started by: Gibbler
3 Replies

5. Solaris

Unable to install the Network Card

Hi, After I installed Solaris 10 in the Intel platform (chipset 865*) network card was not detected, were shall I get this driver? iam new to Solaris. (2 Replies)
Discussion started by: pravin_2929
2 Replies

6. Debian

Kernel source not found. (can't install network card drivers)

I've had no luck with help on linuxquestions so I figured I'd try here. I'm using debian etch. The problem is that I can not install my network card because it says: Makefile:62: *** Linux kernel source not found. Stop. I have the kernel-headers installed. I've looked all over the... (9 Replies)
Discussion started by: Virtuality
9 Replies

7. UNIX for Dummies Questions & Answers

How can I tell which network card is which?

I have three network cards in my unix box. I need to figure out which card corresponds to an assigned IP address. If there some command in unix I can use to make an ethernet interface blink? Any advice would be appreciated. (6 Replies)
Discussion started by: mojoman
6 Replies

8. Solaris

How to identifying the network card ?

Hi Experts, Can we use some command from unix to find the available network interface? I did tried Its listing following, however how can I decide the which vender card is attached e.g. if its hme , bge or some thing else Thanks (7 Replies)
Discussion started by: kumarmani
7 Replies

9. Red Hat

Regarding Network Interface Card

Dear All , While taking backups in one Linux Server , we find one alert came with regard to Network Interface Card. Pl find the below alert. Network Interface Card performance for NIC:eth1 has exceeded Major threshold. Bytes sent and received per second (Average)= 105540.303101... (6 Replies)
Discussion started by: jegaraman
6 Replies

10. Ubuntu

Error on network card

Hi Please can you help me to understand what could be wrong based on what I have captured in the logs: I have run cat /var/log/syslog | grep -i warn, and I got the following output NetworkManager: <warn> Activation (eth3) failed. Dec 23 10:58:25 cmoveldb02 NetworkManager: <warn> (eth3): DHCPv4... (2 Replies)
Discussion started by: fretagi
2 Replies

LEARN ABOUT DEBIAN

vgremove

VGREMOVE(8)						      System Manager's Manual						       VGREMOVE(8)

NAME

       vgremove - remove a volume group

SYNOPSIS

       vgremove [-d|--debug] [-f|--force] [-h|-?|--help] [--noudevsync] [-t|--test] [-v|--verbose] VolumeGroupName [VolumeGroupName...]

DESCRIPTION

       vgremove  allows  you to remove one or more volume groups.  If one or more physical volumes in the volume group are lost, consider vgreduce
       --removemissing to make the volume group metadata consistent again.

       If there are logical volumes that exist in the volume group, a prompt will be given to confirm removal.	You can override the  prompt  with
       -f.

OPTIONS

       See lvm for common options.

       -f, --force
	      Force the removal of any logical volumes on the volume group without confirmation.

       --noudevsync
	      Disable  udev  synchronisation. The process will not wait for notification from udev.  It will continue irrespective of any possible
	      udev processing in the background.  You should only use this if udev is not running or has rules that ignore the devices	LVM2  cre-
	      ates.

SEE ALSO

       lvm(8), lvremove(8), vgcreate(8), vgreduce(8)

Sistina Software UK					 LVM TOOLS 2.02.95(2) (2012-03-06)					       VGREMOVE(8)
All times are GMT -4. The time now is 02:12 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy